MOTEUR / ENGINE
Transcription
MOTEUR / ENGINE
Homologation N° FICHE D’HOMOLOGATION HOMOLOGATION FORM 33/M/09 COMMISSION INTERNATIONALE DE KARTING - FIA MOTEUR / ENGINE SUPER ICC / ICC Constructeur Marque Modèle Type d’admission Durée de l’homologation Nombre de pages Manufacturer Make Model Inlet type Validity of the homologation Number of pages La présente Fiche d’Homologation reproduit descriptions, illustrations et dimensions du moteur au moment de l’homologation CIK-FIA. Le Constructeur a la possibilité de les modifier seulement dans les limites fixées par le Règlement CIKFIA en vigueur. La hauteur du moteur complet sur les photos doit être de 7cm minimum. C.R.S. SRL CRS S1 CLAPETS 6 ans / 6 years 9 This Homologation Form reproduces descriptions, illustrations and dimensions of the engine at the moment of the CIK-FIA homologation. The Manufacturer may modify them, but only within the limits fixed by the CIK-FIA Regulations in force. The height of complete engines on all photos must be minimum 7cm. PHOTO DU MOTEUR CÔTÉ PIGNON PHOTO OF DRIVE SIDE OF ENGINE PHOTO DU MOTEUR CÔTÉ OPPOSÉ PHOTO OF OPPOSITE SIDE OF ENGINE Signature et tampon de l’ASN Signature and stamp of the ASN Signature et tampon de la CIK-FIA Signature and stamp of the CIK-FIA Copyright 2003 by CIK-FIA. All rights reserved. 1 J:\COMMON_GROUP\HOMOLOGATIONS\2004\Matériels 2004\Fiches définitives\CRS 33-M-09.doc Homologation N° 33/M/09 INFORMATIONS TECHNIQUES A TECHNICAL INFORMATION CARACTÉRISTIQUES A CHARACTERISTICS Tolérances Volume du cylindre Alésage d’origine Alésage théorique maximum Course Système de refroidissement Nombre de systèmes de carburation Nombre de canaux de transfert, cylindre/carter Nombre de lumières / canaux d’échappement Forme de la chambre de combustion Matériau de la paroi du cylindre Longueur (entre-axe) de la bielle Volume de la chambre de combustion Volume of cylinder Original Bore Theoretical maximum bore Stroke Cooling system Number of carburation systems 124,569 CM3 55,99 MM 56,06 MM 50,62 MM EAU 1 Number of transfer ducts, cylinder/sump Number of exhaust ports / ducts 5 Shape of the combustion chamber Cylinder wall material Length between the axes of the connecting rod Volume of combustion chamber RAYON VARIABLE + SQUISCH < 125cm³ 3 CROMATE- NIKASIL 108 ±0.1mm 11 C.C. Minimum Modifications autorisées selon le Règlement Technique. Seules les dimensions et cotes qui ne peuvent pas être modifiées doivent figurer sur la Fiche d’Homologation. Modification allowed according to the Technical Regulations. Only the dimensions and readings which may not be changed must be mentioned on the Homologation Form. B ANGLES D’OUVERTURE De l’échappement C B Exhaust Copyright 2003 by CIK-FIA. All rights reserved. Max 199° MATÉRIAU Cylindre Culasse Carter Bielle OPENING ANGLES C Cylinder Cylinder head Sump Connecting rod 2 MATERIAL ALLUMINIUM G-AL-SI 5CU-MG+NIKASIL ALLUMINIUM OU BRONZE ALLUMINIUM G-AL-SI-5CU-MG ACIER 16 NI CR MO 12 J:\COMMON_GROUP\HOMOLOGATIONS\2004\Matériels 2004\Fiches définitives\CRS 33-M-09.doc Homologation N° 33/M/09 DESSIN DU DÉVELOPPEMENT DU CYLINDRE DRAWING OF THE CYLINDER DEVELOPMENT DESSIN DU PIED DU CYLINDRE VUE EN SECTION DU CYLINDRE DRAWING OF THE CYLINDER BASE Copyright 2003 by CIK-FIA. All rights reserved. 3 SECTION VIEW OF CYLINDER J:\COMMON_GROUP\HOMOLOGATIONS\2004\Matériels 2004\Fiches définitives\CRS 33-M-09.doc Homologation N° 33/M/09 DESSIN DE LA CULASSE ET DE LA CHAMBRE DE COMBUSTION DESSIN DU VILEBREQUIN DESSIN INTÉRIEUR DU CARTER DRAWING OF THE CRANKSHAFT Copyright 2003 by CIK-FIA. All rights reserved. DRAWING OF THE CYLINDER HEAD AND OF THE COMBUSTION CHAMBER 4 DRAWING OF THE INSIDE OF SUMP J:\COMMON_GROUP\HOMOLOGATIONS\2004\Matériels 2004\Fiches définitives\CRS 33-M-09.doc Homologation N° 33/M/09 PHOTO DE L’ARRIÈRE PHOTO OF THE BACK DU MOTEUR OF THE ENGINE PHOTO DE L’AVANT DU MOTEUR PHOTO OF THE FRONT OF ENGINE PHOTO DU MOTEUR PARTIE SUPÉRIEURE PHOTO DU MOTEUR PARTIE INFÉRIEURE PHOTO OF THE ENGINE TAKEN FROM BELOW PHOTO OF THE ENGINE TAKEN FROM ABOVE Copyright 2003 by CIK-FIA. All rights reserved. 5 J:\COMMON_GROUP\HOMOLOGATIONS\2004\Matériels 2004\Fiches définitives\CRS 33-M-09.doc Homologation N° 33/M/09 PHOTO DE LA CHAMBRE DE COMBUSTION PHOTO DU PIED DU CYLINDRE PHOTO OF THE BASE OF THE CYLINDER PHOTO DU CARTER ( CÔTÉ JOINT ) PHOTO OF THE SUMP PHOTO D’UNE PARTIE INTÉRIEURE DU ( GASKET FACE ) CARTER Copyright 2003 by CIK-FIA. All rights reserved. 6 PHOTO OF COMBUSTION CHAMBER PHOTO OF AN INTERNAL PART OF THE SUMP J:\COMMON_GROUP\HOMOLOGATIONS\2004\Matériels 2004\Fiches définitives\CRS 33-M-09.doc Homologation N° 33/M/09 DESSIN DE LA BOÎTE À CLAPETS DRAWING OF REED VALVE DESSIN DU COUVERCLE DE LA BOÎTE À CLAPETS DRAWING OF REED VALVE COVER Copyright 2003 by CIK-FIA. All rights reserved. 7 J:\COMMON_GROUP\HOMOLOGATIONS\2004\Matériels 2004\Fiches définitives\CRS 33-M-09.doc Homologation N° 33/M/09 BOÎTE DE VITESSES Couple primaire GEARBOX Primary coupling 18/73 Rapports de boîte de vitesses Gearbox ratios Vitesse Arbre primaire Arbre secondaire Gear Primary shaft Secondary shaft 1ère/1st 2e/2nd 3e/3rd 4e/4th 5e/5th 6e/6th 15 18 21 23 28 31 32 27 26 24 25 24 PHOTOS DE L’ÉCHAPPEMENT Copyright 2003 by CIK-FIA. All rights reserved. Relevé des valeurs obtenues après trois tours moteur Reading of values obtained after three engine revs 124,6° 177,35° 215° 255° 298,25° 343,8° PHOTOS OF THE EXHAUST 8 J:\COMMON_GROUP\HOMOLOGATIONS\2004\Matériels 2004\Fiches définitives\CRS 33-M-09.doc Homologation N° 33/M/09 TECHNICAL DESCRIPTIONS DESCRIPTIONS TECHNIQUES Poids en gr Volume in cm3 Weight in gr Volume in cc 1160 4070 Minimum +/-5 % DESSINS TECHNIQUES TECHNICAL DRAWINGS Contenant toutes les informations permettant de construire cet échappement. Including all the information necessary to build this exhaust. Copyright 2003 by CIK-FIA. All rights reserved. 9 J:\COMMON_GROUP\HOMOLOGATIONS\2004\Matériels 2004\Fiches définitives\CRS 33-M-09.doc
Documents pareils
moteur / engine
dimensions of the engine at the moment of the CIK-FIA
homologation. The Manufacturer may modify them, but only within
the limits fixed by the CIK-FIA Regulations in force.
The height of complete en...
moteur / engine
minimum
combustion
Nombre de segments de piston Number of piston rings
Modifications autorisées selon le Règlement Technique.
Seules les dimensions et cotes qui ne peuvent pas être modifiées doiven...