HEV28P Housing Quick Install Guide

Transcription

HEV28P Housing Quick Install Guide
HEV28P
(Plus)
English
Quick Install Guide
Guide d’installation rapide du Caisson
Guia de Instalación de la Carcasa
Guida di Installazione Rapida
Manual de Insalação Rápida
Kurzanleitung
Handleiding voor snelle installatie
Français
Le modèle HEV28P comporte un caisson, un cardan et un objectif à
changement rapide. Les étapes pour l’installation sont les suivantes :
La cámara HEV28P comprende una carcasa, un cardán y un lente de
cambio rápido. Para efectuar la instalación:
1.
2.
1.
2.
1.
2.
Install the housing. Follow the instructions in this guide.
Install the gimbal. Refer to the Gimbal Quick Install Guide that
comes with the gimbal (green box).
Install the lens. Refer to the Lens Quick Install Guide that comes
with the lens (blue box).
Install the enclosure cover. Follow the instructions in this guide.
4.
3.
4.
Important safeguards
Installation and servicing should be done by qualified technicians to
conform to all local codes and to maintain your warranty.
THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
Before you begin
Junction box (not supplied)
Boîte de raccordement (non
fournie)
Caja eléctrica (no inluida)
Scatola di giunzione (non fornita)
CE SYMBOLE INDIQUE QUE
D’IMPORTANTES INSTRUCTIONS
CONCERNANT LE FONCTIONNEMENT
ET LA MAINTENANCE ACCOMPAGNENT
CETTE UNITÉ.
HEV28P base
Embase HEV28P
Base de la HEV28P
Base HEV28P
Gimbal and lens (shipped
separately)
Cardan et l’objectif
(expedié à part)
Cardán y lentes
(empacado por aparte)
Sospensione cardanica e
obiettivo (forniti
separatamente)
24
AWG
15 VDC
Wiring connection / Branchement des câbles / Conexiones de
cableado / Connessione dei cavi
Coaxial Cables / Câbles coaxiaux /
Cables coaxiales / Cavi Coassiali
Power
Alimentation
Potencia
Alimentazione
Figure 3
408/125
73/22
660/201
18
AWG
185/56
Longueur maximale des câbles d’alimentation électrique (pieds/mètres)
Caméras dotées d’une alimentation électrique ca/cc
295/90
Calibre de fil
1674/510 2664/812
Note
Calculations are based on an unregulated linear power supply which would
be the worst case. Using a regulated or switching power supply can increase the
cable distance. Honeywell recommends using a CSA Certified/UL listed Class 2
power supply to ensure compliance with electrical safety standards.
RG-59
RG-6
Wire gauge
23 AWG*
18 AWG* 14 AWG*
750/229
1500/457 2000/610
Maximum length
RG-11
4S Electrical box installation / Installation sur un coffret de
branchement 4S / Instalación de la caja eléctrica 4S / Installazione
della centralina elettrica 4S
Honeywell recommends the following NVT video transceivers (sold separately
through NVT Inc.):
•
NV-212A (500 ft/152 m—26 Ω)**
•
NV-213A/A-M (1000 ft/305 m—52 Ω)**
•
NV-652R, NV-862R or NV-1662R (3000 ft/914 m—163 Ω)**
** Distances have been calculated using 24 AWG Twisted Pair wire.
Note
We recommend that you measure the wire distance to ensure that the
capability of the twisted pair product is not exceeded. You can measure wire
resistance with an ohmmeter by shorting the two conductors together at the far end,
then measuring the loop resistance out and back. Compare against the following
table.
Maximum length (feet/meters)
Adapter plate (use is
optional)
Plaque d’adaption
(usage optionnel)
Placa adaptadora (uso
opcional)
Piastra di giunzione
(utilizzo opzionale)
4S electrical box (not
supplied)
Coffret de branchement 4S
(non fourni)
Caja eléctria 4S (no incluida)
Centralina elettrica 4S (non
fornita)
AWG
250/
76
18
20
22
HEV28P base
Base HEV28P
Base de la HEV28P
Base HEV28P
24
Note
2
Figure 4
Surface mount installation / Installation en surface / Instalación en
superficie / Installazione con montaggio non ad incasso
Wiring, cabling
Câblage
Alambres, cables
Fili, cablaggio
Breakaway tab for surface
mount cable
Languette détachable pour
câble d’installation en surface
Lengüeta desprendible para
instalar el cable en superficie
Linguetta removibile per cavo
di montaggio senza incasso
500/
152
1000/
305
1500/
457
2000/
610
3000/
914
3Ω
6Ω
13 Ω
19 Ω
26 Ω
40 Ω
5Ω
10 Ω
20 Ω
30 Ω
40 Ω
59 Ω
8Ω
13 Ω
52 Ω
78 Ω
66 Ω
108 Ω
99 Ω
163 Ω
Mounting options
Figure 3 illustrates how to mount the HEV28P directly to a 4S electrical
box:
Adapter plate (when mounting
to ceiling tile)
Plaque d’adaptation (lorsque
le modèle est fixé à un carreau
du plafond)
Placa adaptadora (en
instalaciones en el cielo raso)
Piastra di giunzione (per
montaggio su piastrelle)
Note
1.
2.
Skirt
Embase de blindage
Falda
Collare di rinforzo
3
4
#8-32 x 7/16 inch security screws (x3)
Vis de sécurité n° 8-32 de 7/16 po (3)
Tornillos de seguridad #8-32 x 7/16”
(x3)
Viti di sicurezza 8-32 x 7/16” (x3)
Polycarbonate dome
Dôme en polycarbonate
Domo de policarbonato
Dome in policarbonato
Front cover
Couvre-joint frontal
Placa frontal
Copertura
anteriore
Gasket
Joint statique
Sello
Anello di tenuta
24 VAC
408/125
660/201
1674/510
2664/812
Type de câble
RG-59
RG-6
RG-11
Calibre de fil
23 AWG*
18 AWG*
14 AWG*
750/229
1500/457
2000/610
Retainer plate
Plaque de retenue
Placa de retención
Piastra di blocco
Il modello HEV28P è progettato per essere montato ad incasso o
superficialmente su soffitto o parete. È resistente ai fattori ambientali
esterni per l’utilizzo in luoghi all’aperto o al chiuso. Il kit di installazione
HEV28P (vedere Figura 1) include una piastra di giunzione che può
essere utilizzata per fornire opzioni di montaggio flessibili.
1
Nota
Collegamento cavi
AVVERTENZA!
Si richiede l’utilizzo di alimentatori con certificazione CSA,
classificati UL, classe 2, per la conformità con gli standard di
sicurezza elettrica.
Fare riferimento a Figura 2 per le connessioni dei cavi.
Para que la instalación sea segura, los cables instalados
en la superficie deben ser protegidos por tubos portacables plásticos o metálicos.
Nota
AWG
22
AWG
18
AWG
16
15 VCC
45/14
73/22
185/56
295/90
Alimentazione
24 VCA
408/125
660/201
1674/510
2664/812
15V c.c.
45/14
73/22
185/56
295/90
24V CA
408/125
660/201
1674/510
2664/812
Nota
Los cálculos se basan en una alimentación lineal no regulado que sería
el peor escenario. Si utiliza una fuente de alimentación regulada, puede aumentar
la distancia del cable. Honeywell recomienda usar una fuente de alimentación
Certificada por CSA o Clase 2 de UL para asegurar cumplimiento de las normas
de seguridad eléctricas.
Nota
I calcoli si basano sull’alimentazione lineare non regolata, che
rappresenta il caso peggiore. L’utilizzo di alimentazione regolata o a
commutazione consente di aumentare la distanza del cavo. Honeywell consiglia
l’utilizzo di alimentatori con certificazione CSA, classificati UL, classe 2, per la
conformità con gli standard di sicurezza elettrica.
RG-6
RG-11
14 AWG*
Tipo di cavo
RG-59
RG-6
750/229
1500/457
2000/610
Calibratura fili
23 AWG*
18 AWG*
14 AWG*
750/229
1500/457
2000/610
Lunghezza massima cavo video coassiale (metri)
Lunghezza massima
Máxima longitud del cable UTP de video (pies/meters)
* Anima di acciaio con rivestimento in rame, 95% protezione
intrecciata
Honeywell recomienda los siguientes transceptores NVT (vendidos por NVT Inc
por aparte):
•
NV-212A (500 pi/152 m—26 Ω)**
•
NV-213A/A-M (1000 pi/305 m—52 Ω)**
•
NV-652R, NV-862R or NV-1662R (3000 pi/914 m—163 Ω)**
** Las distancias han sido calculadas usando un cable de par trenzado 24 AWG.
Nota
Se recomienda medir la distancia del cable para asegurar que no va a
exceder la capacidad del cable de par trenzado. La resistencia del cable se puede
medir con un ohmetro cortocircuitando los dos conductores al mismo tiempo en el
extremo alejado y luego midiendo la resistencia del bucle de ida y de vuelta.
Compare el resultado con la siguiente tabla.
Longitud máxima (pies/metros)
AWG
250/76
500/152
1000/
305
1500/
457
2000/
610
3000/
914
18
3Ω
6Ω
13 Ω
19 Ω
26 Ω
40 Ω
5Ω
10 Ω
20 Ω
30 Ω
40 Ω
59 Ω
26 Ω
40 Ω
20
20
5Ω
10 Ω
20 Ω
30 Ω
40 Ω
59 Ω
22
8Ω
17 Ω
33 Ω
48 Ω
66 Ω
22
8Ω
17 Ω
33 Ω
48 Ω
66 Ω
99 Ω
24
13 Ω
26 Ω
52 Ω
78 Ω
108 Ω
24
13 Ω
26 Ω
52 Ω
78 Ω
108 Ω
163 Ω
Nota
2
Suivez les directives de la Figure 3 pour fixer le modèle HEV28P
directement à un coffret de branchement 4S :
Remarque La plaque d’adaptation optionnelle peut être utilisée
pour couvrir les imperfections du mur ou du plafond
autour de l’ouverture du coffret de branchement.
Nota
Si consiglia di misurare la distanza del cavo per evitare di superare la
capacità del cavo a coppia intrecciata. È possibile calcolare la resistenza del cavo
con un ohmetro cortocircuitando i due conduttori insieme alle estremità e
calcolando quindi la resistenza in loop di entrata di ritorno. Eseguire un confronto
seguendo la tabella riportata.
Lunghezza massima (metri)
99 Ω
18
163 Ω
20
Use sólo cable de par trenzado, sin blindaje, de punto a punto.
500/152
1000/305
1500/457
2000/610
3000/
914
3Ω
6Ω
13 Ω
19 Ω
26 Ω
40 Ω
5Ω
10 Ω
20 Ω
30 Ω
40 Ω
59 Ω
22
8Ω
17 Ω
33 Ω
48 Ω
66 Ω
99 Ω
24
13 Ω
26 Ω
52 Ω
78 Ω
108 Ω
163 Ω
Nota
2
Montare direttamente su una centralina
elettrica 4S
Nota
Figura 3 riporta le modalità di montaggio del modello HEV28P
direttamente su una centralina elettrica 4S:
Se puede usar la placa adaptadora opcional para cubrir
cualquier imperfección en la pared o en el cielo raso
alrededor de la apertura de la caja eléctrica.
Nota
Asegure la placa adaptadora (opcional) a la caja eléctrica 4S
utilizando tornillos apropriados (no incluidos).
Asegure la base de la HEV28P con los tornillos #8-32-3/8 de
pulgada (x3).
1.
Instalación en la superficie
1.
Pour les installations utilisant la plaque d’adaptation, fixez
l’embase de blindage avec les trois vis à tête cylindrique bombée
n° 8-32 de 7/8 po. fournies.
Nota
Remarque Pour les installations qui n’utilisant pas la plaque
d’adaptation, utilisez des vis adaptées à votre installation (non fournies).
2.
Fixez la base du caisson HEV28P avec les trois vis à métal n° 8-32
de 3/8 po. fournies.
2.
1.
Your camera is ready to go to work for you.
2.
Cuando no utilize la placa adaptadora, utilize tornillos
que se adjusten a las necesidades de su instalación (no
incluidos).
1.
Asegure la base de la HEV28P con los tornillos #8-32 x 3/8 de
pulgada (x3) incluidos.
Nota
Siga las indicaciones de la Figura 5 para empotrar la unidad HEV28P en
el cielo raso o en la pared.
En caso de utilizar la placa adaptadora en su instalación, asegure la
base de la HEV28P con los tornillos #8-32 x 7/8 de pulgada (x3)
incluidos.
Cuando no utilize la placa adaptadora, utilize tornillos que se adjusten a
las necesidades de su instalación (no incluidos).
3
Pasos siguientes
1.
Installez le cardan. Pour ce faire, consultez le Guide d’installation
rapide du cardan, livré avec ce dernier (boîte verte).
Installez l’objectif. Pour ce faire, consultez le Guide d’installation
rapide de l’objectif, livré avec celui-ci (boîte bleue).
2.
Instale el cardán. Consulte la Guía de Instalación Rápida del
Cardán incluida con el cardán en la caja verde.
Instale el lente. Consulte la Guía de Instalación Rápida del Lente
incluida con el lente en la caja azul.
Do not use harsh or abrasive cleaners which can
scratch the polycarbonate dome and reduce visibility
for the camera.
If the camera view is obstructed by scratches, remove the front plate
and rotate to find a part of the dome that is not scratched.
If the polycarbonate dome is damaged or scratched beyond use,
contact your distributor or salesperson to order a dome replacement.
Figure 7 illustrates how to replace the HEV28P dome:
2.
3.
4.
5.
Use the security hex key (supplied) to loosen the three #8-32 x 7/
16 inch security screws securing the HEV28P lid to the base.
Use a Phillips screwdriver to remove the three #8-32 x 5/16 inch
machine screws that attach the dome retainer plate to the front
cover.
Remove the damaged dome and replace it with the new dome.
Use a Phillips screwdriver to attach the dome retainer plate to the
HEV28P front plate with the screws you removed in step 2.
Use the security hex key to secure the HEV28P lid to the base.
4
Fixation du couvercle
4
Asegure el domo de la unidad HEV28P a su base con los tres tornillos
de seguridad #8-32 x 7/16” (vea la Figura 6).
Votre caméra est prête à l’usage.
¡Su cámara esta lista!
Entretien du dôme
Mantenimiento de rutina
Utilisez un produit nettoyant liquide non abrasif ordinaire pour retirer la
poussière et la saleté du dôme HEV28P.
Use cualquier detergente líquido común para remover grasa o suciedad
del domo de la HEV28P.
Mise en garde N’utilisez pas de produits nettoyants puissants ou
abrasifs qui risquent de rayer le dôme en
polycarbonate et de réduire la visibilité de la
caméra.
Precaución No use limpiadores abrasivos o muy fuertes porque
pueden rayar el domo de policarbonato y reducir la
visibilidad de la cámara.
Remplacement du dôme
Si le dôme en polycarbonate est endommagé ou rayé au point d’être
inutilisable, contactez votre distributeur ou un représentant des ventes
pour en commander un autre. Suivez les directives de la Figure 7 pour
remplacer le dôme HEV28P :
2.
3.
4.
5.
Utilisez la clé hexagonale de sécurité (fournie) pour retirer les trois
vis de sécurité n° 8-32 de 7/16 po fixant le dôme HEV28P à la
base.
Utilisez un tournevis à tête cruciforme pour retirer les trois vis
metal n° 8-32 de 5/16 po qui fixent la plaque de retenue du dôme
au couvre-joint frontal.
Retirez le dôme endommagé et remplacez-le par le nouveau.
Utilisez un tournevis à tête cruciforme pour attacher la plaque de
retenue du dôme au couvre-joint frontal de la caméra HEV28P
avec les vis que vous avez retirées à l’étape 2.
Utilisez la clé hexagonale de sécurité pour attacher le dôme
HEV28P à la base.
Quando non si utilizza la piastra di giunzione, usare le
viti adatte all’installazione (non fornite).
Fissare la base HEV28P con le viti senza dado 8-32 x 3/8" (x3) in
dotazione.
Figura 5 riporta le modalità di montaggio ad incasso del modello
HEV28P direttamente su un soffitto o parete.
Per l’installazione della piastra di giunzione, fissare la base HEV28P con
le viti a testa orientabile 8-32 x 7/8" (x3) in dotazione.Quando non si
utilizza la piastra di giunzione, usare le viti adatte all’installazione (non
fornite).
3
Passaggi successivi
1.
Installare la sospensione cardanica. Fare riferimento alla Guida di
installazione rapida della sospensione cardanica in dotazione con
la sospensione cardanica (scatola verde).
Installare l’obiettivo. Fare riferimento alla Guida di installazione
rapida dell’obiettivo in dotazione con l’obiettivo (scatola blu).
Asegure el domo
Fixez le dôme du modèle HEV28P à la base avec trois vis de sécurité n°
8-32 de 7/16 po (voir la Figure 6).
Si des rayures apparaissent dans le champ de la caméra, retirez le
couvre-joint frontal et faites-le tourner jusqu’à ce que vous trouviez une
partie non rayée sur le dôme.
Par l’installazione della piastra di giunzione, fissare il collare di
rinforzo con le viti a testa orientabile 8-32 x 7/8” (x3) in dotazione.
Montaggio ad incasso
2.
Routine maintenance
Fissare la piastra di giunzione alla centralina elettrica 4S
utilizzando le viti apposite (non fornite).
Fissare la base HEV28P con le viti senza dado 8-32 x 3/8" (x3) in
dotazione.
Fare riferimento alla Figura 4 per le modalità di montaggio del modello
HEV28P su un soffitto o parete.
2.
Suivez les directives de la Figure 5 pour fixer le modèle HEV28P à un
plafond ou à un mur.
Pour les installations utilisant la plaque d’adaptation, fixez la base du
caisson HEV28P avec les trois vis à tête cylindrique bombée n° 8-32 de
7/8 po. fournies. Pour les installations qui n’utilisant pas la plaque
d’adaptation, utilisez des vis adaptées à votre installation (non fournies).
La piastra di giunzione può essere utilizzata per coprire
eventuali imperfezioni del soffitto o parete circostanti
l’apertura della centralina elettrica. L’utilizzo della piastra
di giunzione è opzionale.
Montaggio non ad incasso
En caso de utilizar la placa adaptadora en su instalación, asegure
la falda con los tornillos #8-32 x 7/8 de pulgada (x3) incluidos.
Instalación empotrada
Installation encastrée
Étapes suivantes
2.
Siga las indicaciones de la Figura 4 para instalar la unidad HEV28P en
el cielo raso o en la pared:
Suivez les directives de la Figure 4 pour fixer le modèle HEV28P à un
plafond ou à un mur :
Opzioni di montaggio
Siga las indicaciones de la Figura 3 para instalar la cámara HEV28P
directamente a una caja eléctrica 4S:
2.
Installation en surface
Utilizzare solo un cavo a coppia intrecciata punto a punto.
Opciones de instalación
1.
Fixez la plaque d’adaptation optionnelle au coffret de
branchement 4S à l’aide de vis adaptées à l’installation (non
fournies).
Fixez la base du caisson HEV28P avec les trois vis à métal n° 8-32
de 3/8 po. fournies.
Honeywell consiglia i seguenti ricetrasmettitori video NVT (venduti separatamente
tramite NVT Inc.):
•
NV-212A (152 m—26 Ω)**
•
NV-213A/A-M (305 m—52 Ω)**
•
NV-652R, NV-862R o NV-1662R (914 m—163 Ω)**
** Le distanze sono state calcolate in base al cavo a coppia intrecciata 24 AWG.
250/76
Instalar directamente a una caja
eléctrica 4S
Fixation directe à un coffret de
branchement 4S
Lunghezza massima cavo video UTP (metri)
AWG
Remarque Utilisez uniquement un fil UTP point à point.
3
RG-11
* Núcleo de accro revestido de cobre, 95% blindaje de malla
19 Ω
Secure the HEV28P dome enclosure to the base with three #8-32 x 7/16
inch security screws (see Figure 6).
16
AWG
18 AWG*
13 Ω
Install the gimbal. Refer to the Gimbal Quick Install Guide that
comes with the gimbal (green box).
Install the lens. Refer to the Lens Quick Install Guide that comes
with the lens (blue box).
18
AWG
23 AWG*
6Ω
2.
22
AWG
RG-59
3Ω
1.
24
AWG
Calibre
Distancia máxima
Options de montage
Calibratura fili
Tipo de cable
18
2
Lunghezza massima cavo di alimentazione (metri)
Videocamere con alimentazione CA/c.c.
AWG
24
Máxima longitud del cable coaxial de video (pies/metros)
1000/305 1500/457 2000/610 3000/914
Istruzioni per i cavi
Suministro
de potencia
500/152
Secure the HEV28P base with #8-32 x 3/8 inch machine screws
(x3) supplied.
Secure the cover
Máxima longitud para el cable de suministro de potencia (pies/
metros) Cámaras con suministro CA/CC
250/76
Next steps
1.
Per un’installazione in condizioni di sicurezza, i cavi
montati in superficie devono essere protetti da un
rivestimento cavi in metallo o plastica.
Pautas para cables
AWG
1.
#8-32 x 5/16 inch machine screws (x3)
Vis metal n° 8-32 de 5/16 po (3)
Tornillos para metal #8-32 x 5/16” (x3)
Viti di securezza senza dado 8-32 x 5/
16” (x3)
Panoramica sull’installazione
Siga las indicaciones de la Figura 2 para conectar los cables de video y
de potencia.
Longueur maximale (pieds/metres)
When not using the adapter plate, use screws
appropriate to your installation (not supplied).
Caution
Dome replacement / Remplacement du dôme / Reemplazo del
domo / Sostituzione del dome
295/90
Remarque Les longueurs ont été calculées en utilisant un fil à paire torsadée de
calibre 24 AWG.Nous vous recommandons de mesurer la longueur du fil afin de
vous assurer que le système n’excède pas les capacités du produit à paire
torsadée. Vous pouvez mesurer la résistance du fil à l’aide d’un ohmmètre en courtcircuitant les deux conducteurs à l’extrémité distante, puis en mesurant la
résistance de la boucle dans un sens puis dans l’autre. Comparez vos résultats au
tableau suivant.
For adapter plate installations, secure the skirt with #8-32 x 7/8
inch pan head screws (x3) supplied.
Dome replacement
Figure 7
185/56
Honeywell recommande l’utilisation des émetteurs-récepteurs vidéo NVT suivants
(vendus séparément par NVT Inc.):
•
NV-212A (500 pi/152 m—26 Ω)**
•
NV-213A/A-M (1000 pi/305 m—52 Ω)**
•
NV-652R, NV-862R or NV-1662R (3000 pi/914 m—163 Ω)**
** Les longueurs ont été calculées en utilisant un fil à paire torsadée de calibre 24
AWG.
Secure the optional adapter plate to the 4S electrical box using
appropriate screws (not supplied).
Secure the HEV28P base with #8-32 x 3/8 inch machine screws
(x3) supplied.
Use regular liquid cleaners to remove dirt and grime from the HEV28P
dome.
#8-32 x 7/16 inch security screws (x3)
Vis de sécurité n° 8-32 de 7/16 po (3)
Tornillos de seguridad #8-32 x 7/16”
(x3)
Viti di sicurezza 8-32 x 7/16” (x3)
73/22
Flush mount
2.
Dome enclosure
Dôme
Domo
Involucro del
dome
45/14
Longueur maximale des câbles vidéo UTP (pieds/mètres)
Figure 5 illustrates how to mount the HEV28P flush to a ceiling or wall.
For adapter plate installations, secure the HEV28P base with #8-32 x 7/
8 inch pan head screws (x3) supplied.
When not using the adapter plate, use screws appropriate to your
installation (not supplied).
HEV28P base
Base de la HEV28P
Base HEV28P
Base HEV28P
15 VDC
1.
Flush mount installation / Installation pour fixation encastrée /
Instalación empotrada / Installazione con montaggio ad incasso
Aprire la confezione. Verificare che gli elementi ricevuti corrispondano a
quelli elencati nel modulo d’ordine e nel tagliando della confezione.
Oltre a questa Guida di installazione rapida, la confezione dell’unità
HEV28P deve comprendere quanto elencato di seguito:
•
Un involucro HEV28P
•
Un kit hardware HEV28P
•
Una scheda di garanzia del prodotto
Nel caso di parti mancanti o danneggiate, rivolgersi al rivenditore
presso il quale è stata acquistata l’unità o chiamare il Servizio clienti di
Honeywell.
Es imprescindible utilizar una alimentación de potencia Clase
2 certificada por CSA o listado por UL para cumplir con las
normas eléctricas de seguridad.
Calibre
* Âme d’acier recouvert de cuivre, blindage tressé à 95%
The adapter plate can be used to cover ceiling or wall
imperfections around the electrical box opening. Use of
the adapter plate is optional.
Note
Enclosure cover installation / Installation du couvercle du caisson /
Instalación del domo / Installazione copertura involucro
16
AWG
Follow Figure 4 to mount the HEV28P to a ceiling or wall:
1.
HEV28P base
Base HEV28P
Base HEV28P
Base HEV28P
18
AWG
Longeur maximale
Surface Mount
1.
Figure 6
26 Ω
48 Ω
Use point-to-point Unshielded Twisted Pair wire only.
2.
Adapter plate (for
mounting to ceiling tile)
Plaque d’adaptation
(lorsque le modèle est
fixé à un carreau du
plafond)
Placa adaptadora (en
instalaciones en el cielo
raso)
Piastra di giunzione (per
montaggio su piastrelle)
33 Ω
Mount directly to a 4S electrical box
HEV28P base
Base HEV28P
Base HEV28P
Base HEV28P
Figure 5
17 Ω
22
AWG
Longueur maximale des câbles vidéo coaxiaux (pieds/mètres)
* Copper clad steel core, 95% braided shield
Power: 2.1 mm male jack center pin
Alimentation: Prise mâle à broche
centrale 2,1 mm
Potencia: Enchufe macho pin central de 2,1 mm
Alimentazione: 2,1 mm jack maschio a pin centrale
24
AWG
Remarque Les calculs sont basés sur le cas le plus défavorable, à savoir celui
d’une alimentation électrique linéaire non régulée. L’utilisation d’une alimentation
électrique régulée ou à découpage peut permettre d’augmenter la longueur de
câble. Honeywell recommande l’utilisation d’une alimentation de classe 2, certifié
CSA/homologué UL, pour assurer le respect des normes de sécurité électrique.
Longueur maximale des câbles vidéo coaxiaux (pieds/mètres).
UTP video cable maximum length (feet/meters)
Black Noir Negro Nero -
Type
d’alimentation
QUESTO SIMBOLO INDICA CHE
L’UNITÀ È ACCOMPAGNATA DA
IMPORTANTI INFORMAZIONI PER
L’USO E LA MANUTENZIONE.
Prima di iniziare
Directives concernant les câbles
16
AWG
Cable type
ATTENZIONE: PER RIDURRE IL RISCHIO DI SCOSSA
ÉLETTRICA, NON RIMUOVERE
LA COPERTURA. NON CONTIENE PARTI RIPARABILI
DALL’UTENTE. FARE ESEGUIRE LA MANUTENZIONE A
PERSONALE QUALIFICATO.
¡ADVERTENCIA!
Remarque Pour assurer la sécurité de l’installation, les câbles
montés en surface doivent être protégés par des enveloppes de câble métalliques ou en plastique.
Coaxial video cable maximum length (feet/meters)
Video: Unshielded Twisted
Pair wire
Vidéo: Fil à paire torsadée
non blindée
Video: Cable de par
trezado, no blindado
Video: Non schermati.
Cavo a coppia intrecciata
Video: female BNC wire
Vidéo: câble BNC femelle
Video: cable hembra BNC
Video: femmina cavo BNC
Red +
Rouge +
Rojo +
Rosso +
UTP Cables / Câbles UTP / Cables UTP
(par trenzado no blindado) / Cavi UTP
45/14
22
AWG
QUESTO SIMBOLO INDICA LA
PRESENZA DI TENSIONI
PERICOLOSE ALL’INTERNO
DELL’UNITÀ; RISCHIO DI
SCOSSA ÉLETTRICA.
ATTENZIONE
RISCHIO DI SCOSSA
ÉLETTRICA
NON APRIRE
Conexiones de cableado
Suivez les directives de la Figure 2 pour brancher les câbles vidéo et
d’alimentation.
Wire gauge
Power
supply
1
Vous devez utiliser un adaptateur de courant de classe 2,
certifié CSA/homologué UL, pour assurer le respect des
normes de sécurité sur l’électricité.
Power supply cable maximum length (feet/meters) Cameras
with AC/DC power supplies
ESTE SÍMBOLO INDICA QUE
INSTRUCCIONES IMPORTANTES
DE FUNCIONAMIENTO Y
MANTENIMIENTO ACOMPAÑAN
ESTA UNIDAD.
La cámara serie HEV28P ha sido diseñada para ser instalada o
empotrada en la superficie de la pared o del cielo raso. La cámara
HEV28P ha sido sellada herméticamente para poder usarla en
interiores o exteriores. El kit de instalación (vea la Figura 1) incluye una
placa adaptadora de uso opcional, que ofrece opciones de instalación
más flexibles.
MISE EN GARDE!
Cable guidelines
24 VAC
Figure 2
Branchement des câbles
For secure installations, surface-mounted cables
should be protected by plastic or metal cable covers.
L’installazione e la manutenzione devono essere eseguite da tecnici
qualificati per la conformità alle norme locali e per mantenere la validità
della garanzia.
Descripción general
Survol de l’installation
1
Informazioni importanti per la
sicurezza
Desempaque todo. Confirme que los artículos recibidos corresponden
a los indicados en el formulario de pedido y la lista de empaque. La
caja de la unidad HEV28P debe incluir, además de esta Guía de
Instalación Rápida:
•
Una caja de protección para la cámara HEV28P
•
Un kit de instalación para la HEV28P
•
Una tarjeta de Garantía de Producto
Si hacen falta partes o si hay partes dañadas, contacte al distribuidor
donde compró la cámara o llame al departamento de Atención a
Clientes de Honeywell. Va a necesitar un destornillador Phillips y
alicates de corte lateral para efectuar la instalación.
La caméra HEV28P est conçue pour être encastrée ou en surface dans
un mur ou un plafond. Elle est étanche et peut donc être installée à
l’intérieur comme à l’extérieur. La trousse d’installation pour votre
caméra HEV28P (voir la Figure 1) comprend une plaque d’adaptation
qui peut être utilisée pour offrir un maximum d’options de montage.
The use of a CSA Certified/UL Listed Class 2 power supply is
required to ensure compliance with electrical safety standards.
Adapter plate
Plaque d’adaptation
Placa adaptadora
Piastra di giunzione
3.
Antes de comenzar
WARNING!
Note
HEV28P dome
enclosure
Dôme HEV28P
Domo de la HEV28P
Involucro dome HEV28P
PRECAUCIÓN: PARA REDUCIR EL RIESGO DE
CHOQUES ELÉCTRICOS, NO QUITE LA CUBIERTA.
EL MANTENIMIENTO Y EL SERVICIO DEBEN SER
HECHOS SÓLO POR PERSONAL CALIFICADO.
Déballez l’ensemble des éléments. Vérifiez que les articles reçus
correspondent à ceux répertoriés sur le bon de commande et sur le
bordereau d’emballage. L’emballage du HEV28P doit comprendre, en
plus de ce guide d’installation rapide :
•
Un caisson HEV28P
•
Une trousse d’installation du caisson HEV28P
•
Une carte de garantie du produit
Si certaines pièces manquent ou sont endommagées, contactez le
distributeur auprès duquel vous avez acheté la caméra ou appelez le
service à la clientèle de Honeywell. Pour mener à bien l’installation, il
vous faudra un tournevis à tête cruciforme et des pinces coupantes.
Wiring connections
Installare l’alloggiamento. Seguire le istruzioni riportate in questa
guida.
Installare la sospensione cardanica. Fare riferimento alla Guida di
installazione rapida della sospensione cardanica in dotazione con
la sospensione cardanica (scatola verde).
Installare l’obiettivo. Fare riferimento alla Guida di installazione
rapida dell’obiettivo in dotazione con l’obiettivo (scatola blu).
Installare la copertura dell’involucro. Seguire le istruzioni riportate
in questa guida.
2.
ESTE SÍMBOLO INDICA QUE
DENTRO DE ESTA UNIDAD HAY
TENSIÓN PELIGROSA QUE
PUEDE CAUSAR CHOQUES
ELÉCTRICOS.
CUIDADO
RIESGO DE CHOQUE
ELÉCTRICO.
NO LO ABRA.
Instructions préliminaires
The HEV28P is designed to be flush or surface mounted on a wall or
ceiling. It is weather-sealed for indoor or outdoor locations. Your
HEV28P installation kit (see Figure 1) comes with an adapter plate that
can be used to provide the most flexible mounting options.
1.
4.
Para mantener la garantía vigente y cumplir con todos los códigos
locales, la instalación y el servicio a la unidad deben ser realizados sólo
por técnicos qualificados.
Follow Figure 2 for the wiring connection.
kirt—use with surface
mount installation
Embase—utilisée pour
une installation en surface
Falda—use cuando se
instala en superficie
Collare di rinforzo—da
utilizzare con le
installazioni a montaggio
non ad incasso
4.
L’installation et l’entretien doivent être effectués par des techniciens
qualifié pour veiller au respect de tous les codes locaux et pour
maintenir vos droits à bénéficier de la garantie.
ATTENTION: POUR RÉDUIRE LE RISQUE DE CHOC
ÉLECTRIQUE, NE RETIREZ PAS LE COUVERCLE.
AUCUNE PIÈCE DONT L’ENTRETIEN PEUT ÊTRE
ASSURÉ PAR L’UTILISATEUR NE SE TROUVE À
L’INTÉRIEUR. CONFIEZ LA MAINTENANCE À DES
TECHNICIENS QUALIFIÉS SPÉCIALISÉS DANS
L’ENTRETIEN
Installation overview
1
3.
Precauciones importantes
CE SYMBOLE INDIQUE QU’À
L’INTERIEUR DE CETTE UNITÉ PASSE
UN COURANT DE TENSION
SUFFISAMMENT ÉLEVÉE POUR RISQUE
DE PROVOQUER UN CHOC
ÉLECTRIQUE.
Il modello HEV28P è costituito da un alloggiamento, una sospensione
cardanica e un obiettivo a sostituzione rapida. Per completare
l’installazione:
Instale la carcasa siguiendo las instrucciones de esta guía.
Instale el cardán. Consulte la Guía de Instalación Rápida del
Cardán incluida con el cardán en la caja verde.
Instale el lente. Consulte la Guía de Instalación Rápida del Lente
incluida con el lente en la caja azul.
Instale la cubierta de la caja protectora siguiendo las
instrucciones de esta guía.
Consignes importantes de sécurité
RISQUE DE CHOC
ÉLECTRIQUE.
NE PAS OUVRIR
Unpack everything. Check that the items received match those listed on
the order form and packing slip. The HEV28P packing box should
include, in addition to this Quick Install Guide:
•
One HEV28P enclosure
•
One HEV28P hardware kit
•
One Product Warranty card
If any parts are missing or damaged, contact the dealer you purchased
the camera from or call Honeywell Customer Service.
Installation components / Installation des composants /
Componentes de instalación / Componenti di installazione
Installez le caisson. Suivez les instructions figurant dans ce guide.
Installez le cardan. Pour ce faire, consultez le Guide d’installation
rapide du cardan, livré avec ce dernier (boîte verte).
Installez l’objectif. Pour ce faire, consultez le Guide d’installation
rapide de l’objectif, livré avec celui-ci (boîte bleue).
Installez le couvercle du caisson. Suivez les instructions figurant
dans ce guide.
ATTENTION
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER.
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL
Figure 1
Italiano
The HEV28P comprises a housing, a gimbal, and a quick change lens.
To complete the installation:
3.
Figures
Español
Si la visión de la cámara está obstruida porque el domo está muy
rayado, saque la placa frontal y dele vuelta hasta encontrar una parte
del domo que no esté rayada.
Para reemplazar el domo
Si el domo de policarbonato se llega a dañar o está rayado de tal forma
que no se pueda usar, contacte a su distribuidor o a su agente de
ventas para pedir un domo de reemplazo. Siga las indicaciones de la
Figura 7 para instalar el nuevo domo de la HEV28P:
1.
2.
3.
4.
5.
Desatornille los tres tornillos de seguridad #8-32 x 7/16 in. que
sostienen la cubierta de la HEV28P en la base con la llave
hexagonal de seguridad provista.
Con un destornillador Phillips saque los tres tornillos de fijación
para metal #8-32 x 5/16” que aseguran la placa de retención a la
cubierta frontal.
Quite el domo dañado e instale el nuevo domo en su lugar.
Con un destornillador Phillips vuelva a asegurar la placa de
retención del domo a la placa frontal de la unidad HEV28P,
utilizando los tornillos que quitó en el paso 2.
Con la llave de seguridad hexagonal, asegurar la cubierta de la
HEV28P a su base.
4
Fissare la copertura
Fissare l’involucro del dome HEV28P alla base utilizzando tre viti di
sicurezza num. 8-32 x 7/16" (vedere Figura 6).
La videocamera è pronta per l’utilizzo.
Manutenzione di routine
Utilizzare detergenti liquidi per rimuovere lo sporco e il grasso dal dome
HEV28P.
Avvertenza Non utilizzare detergenti abrasivi o troppo aggressivi
che possano graffiare il dome di policarbonato e
ridurre la visibilità della videocamera.
Se la vista della videocamera è ostruita da graffi, rimuovere la piastra
anteriore e ruotare fino a trovare una parte liscia e uniforme.
Sostituzione del dome
Se i danni e i graffi sul dome in policarbonato non rendono possibile il
relativo utilizzo, contattare il rivenditore autorizzato per ordinare un
dome di sostituzione. Per sostituire il dome HEV28P (vedere Figura 7):
1.
2.
3.
4.
5.
Utilizzare una chiave esagonale di sicurezza (in dotazione) per
allentare le tre viti di sicurezza 8-32 x 7/16" che fissano il coperchio
HEV28P alla base.
Utilizzare un giravite Phillips per rimuovere le tre viti senza dado 832 x 5/16" che fissano la piastra di blocco del dome alla copertura
anteriore.
Rimuovere il dome danneggiato e sostituirlo con la nuova unità.
Utilizzare un giravite Phillips per fissare la piastra di blocco del
dome alla piastra anteriore HEV28P con le viti che sono state
rimosse nel passaggio 2.
Utilizzare una chiave esagonale di sicurezza per fissare il
coperchio HEV28P alla base.
Figures
Figure 1
Português
Componentes de instalação / Komponenten für den Einbau /
Installatiecomponenten
Caixa de junção (não fornecida)
Anschlussdose (nicht mitgeliefert)
Aansluitdoos (niet bijgeleverd)
Placa adaptadora
Adapterplatte
Adapterplaat
A câmara HEV28P é composta por um alojamento, um cardan e uma
objectiva de substituição rápida. Para efectuar a instalação:
Das Modell HEV28P besteht aus einem Gehäuse, einem Kardan und
einem Schnellwechsel-Objektiv. So führen Sie den Einbau durch:
De HEV28P omvat een behuizing, een cardanische ophanging en een
snel verwisselbare lens. Om de installatie volledig te maken:
1.
2.
1.
1.
2.
Instale o alojamento. Siga as instruções indicadas neste manual.
Instale o cardan. Consulte o Manual de Instalação Rápida do
Cardan fornecido com o cardan (caixa verde).
Instale a objectiva. Consulte o Manual de Instalação Rápida da
Objectiva fornecido com a objectiva (caixa azul).
Instale a tampa da caixa. Siga as instruções indicadas neste
manual.
3.
4.
2.
3.
4.
Orla—utilize com a
montagem à superficie
Einfassung—wird bei
Montage über Putz
verwendet
Rand—voor gebruik bij
oppervlaktemontage
A instalação e manutenção devem ser efectuadas por técnicos
qualificados para assegurar a conformidade com todas as regras locais
e manter a garantia.
RISCO DE
ELECTROCUSSÃO
NÃO ABRIR
Cardan e objectiva
(enviados
separadamente)
Kardan und Objektiv
(separat versnadt)
Cardanische ophanging
en lens (apart verpakt)
CUIDADO: PARA REDUZIR O RISCO DE CHOQUES
ELÉCTRICOS, NÃO REMOVA A TAMPA (OU A
PARTE DE TRÁS). NÃO EXISTEM NO INTERIOR
PEÇAS QUE POSSAM SER REPARADAS PELO
UTILIZADOR. TODA A MANUTENÇÃO DEVE SER
EFECTUADA POR PESSOAL QUALIFICADO.
Video: Fio BNC fèmea
Video: Buchse BNC-Leitung
Video: vrouwelijk BNC draad
Alimentação
Strom
Voeding
Figure 3
Preto Schwarz Zwart -
GEFAHR EINES
STROMSCHLAGS NICHT
ÖFFNEN
ESTE SÍMBOLO INDICA QUE
EXISTEM INSTRUÇÕES
IMPORTANTES PARA A
OPERAÇÃO E MANUTENÇÃO
DESTA UNIDAD.
Placa adaptadora
(utilização opcional)
Adapterplatte
(Verwendung ist
optional)
Adapterplaat (gebruik is
optioneel)
Video: Fio de par
entrançado não blindado
Video: unabgeschirmt.
Verdrilltes Doppekabel
Video: Onafgeschermd
Gevlochten paar draad
1
Das Modell HEV28P ist für die Wand- oder Deckenmontage über oder
unter Putz ausgelegt. Das Modell ist sowohl innerhalb als auch
außerhalb von Gebäuden wetterbeständig. Ihr HEV28P-Montagesatz
enthält eine Adapterplatte, mit der Sie bei der Montage eine
größtmögliche Flexibilität erhalten (siehe Abbildung 1).
1
Patilha separável para cabo
de montagem à superficie
Abreißlasche für über Putz
verlegtes Kabel
Uitbreeklip voor kabel bij
oppervlaktemontage
Figure 5
Placa adaptadora (para
montagem no tecto)
Adapterplatte (für Montage an
einer Deckenplatte)
Adapterplaat (voor montage
op plafondplaat)
Orla
Einfassung
Rand
Instalação de montagem encastrada / Montage unter Putz /
Ingebouwde montage
Placa adaptadora (para
montagem no tecto)
Adapterplatte (für
Montage an einer
Deckenplatte)
Adapterplaat (voor
montage op plafondplaat)
24
AWG
22
AWG
18
AWG
16
AWG
15 VDC
45/14
73/22
185/56
24 VAC
408/125
660/201
1674/510
Hinweis
15 V Gleichstrom
45/14
73/22
185/56
295/90
RG-6
RG-11
Espessura do fio
23 AWG*
18 AWG*
14 AWG*
750/229
1500/457
2000/610
Nota
É recomendável medir a distância dos fios para assegurar que a
capacidade do produto de par entrançado não é ultrapassada. Pode medir a
resistência do fio com um ohmímetro fazendo um contacto de curto-circuito entre
os dois condutores na extremidade mais afastada e medindo a resistência do anel
de saída e de retorno. Compare os resultados com a seguinte tabela.
Comprimento total (pés/metros)
Base HEV28P
HEV28P-Sockel
HEV28P basis
24 V Wech- 408/125
selstrom
500/152
18
3Ω
6Ω
1000/305 1500/457
1674/510
2664/812
Hinweis Die Berechnungen basieren auf ungeregelten linearer
Stromversorgung, was den schlechtesten Fall darstellen würde. Durch die
Verwendung einer geregelten Stromversorgung oder einem Schaltnetzteil kann die
Kabelstrecke erhöht werden. Honeywell empfiehlt die Verwendung einer CSAzertifizierten/UL-gelisteten Klasse 2-Stromversorgung, um die Einhaltung der
elektrischen Sicherheitsstandards sicherzustellen.
Kabeltyp
RG-59
Drahtquerschnitt
RG-6
13 Ω
19 Ω
Hinweis Wir empfehlen, die Leitungsentfernung nachzumessen, um
sicherzustellen, dass das Leistungsvermögen des verdrillten Doppelkabels nicht
überschritten wird. Sie können die Leitungsentfernung mit einem
Widerstandsmessgerät messen, indem Sie die beiden Leiter am äußeren Ende
kurzschließen und dann den Schleifenwiderstand hinaus und zurück messen.
Vergleichen Sie die Werte mit der folgenden Tabelle.
20
5Ω
10 Ω
22
8Ω
17 Ω
24
13 Ω
26 Ω
40 Ω
59 Ω
66 Ω
99 Ω
13 Ω
26 Ω
52 Ω
78 Ω
108 Ω
163 Ω
Utilize apenas fios de Par Entrançado não Blindados ponto-a-ponto.
Opções de montagem
1500/457
Honeywell empfiehlt die folgenden NVT-Video-Transceiver (separat von NVT Inc.
verkauft):
•
NV-212A (500 ft/152 m—26 Ω)**
•
NV-213A/A-M (1000 ft/305 m—52 Ω)**
•
NV-652R, NV-862R oder NV-1662R (3000 ft/914 m—163 Ω)**
** Die Entfernungen wurden mit einem Kabel vom Typ „24 AWG verdrilltes
Doppelkabel“ ermittelt.
13 Ω
48 Ω
Maximale Länge (Fuß/Meter)
295/90
24 VAC
408/125
660/201
1674/510
2664/812
Opmerking De berekeningen zijn gebaseerd op ongereguleerde lineaire
voeding in het ergste geval. Bij gebruik van een gereguleerde of geschakelde
voeding kan de kabelafstand worden vergroot. Honeywell beveelt het gebruik aan
van een CSA Certified/UL listed Class 2 voeding om te kunnen voldoen aan de
elektrische veiligheidsnormen.
Coaxiale videokabel maximum lengte (voet/meter)
Kabeltype
RG-59
RG-6
RG-11
Draaddiameter
23 AWG*
18 AWG*
14 AWG*
750/229
1500/457
2000/610
Opmerking Wij bevelen aan de draadafstand te meten om er zeker van te zijn dat
de capaciteit van het gevlochten draad niet wordt overschreden. U kunt de
draadweerstand meten met een ohmmeter door de twee aders aan het uiteinde
met elkaar te verbinden, en vervolgens de lusweerstand heen en terug te meten.
Vergelijk met de volgende tabel.
Maximumlengte (voet/meter)
AWG
250/76
500/152
1000/305 1500/457
18
3Ω
6Ω
13 Ω
20
5Ω
10 Ω
20 Ω
2000/610
3000/
914
19 Ω
26 Ω
40 Ω
30 Ω
40 Ω
59 Ω
2000/610
3000/914
22
8Ω
17 Ω
33 Ω
48 Ω
66 Ω
99 Ω
19 Ω
26 Ω
40 Ω
24
13 Ω
26 Ω
52 Ω
78 Ω
108 Ω
163 Ω
20 Ω
30 Ω
40 Ω
59 Ω
33 Ω
48 Ω
66 Ω
99 Ω
52 Ω
78 Ω
108 Ω
163 Ω
500/152 1000/305 1500/457
Hinweis Verwenden Sie nur Punkt-zu-Punkt-UTP-Leitungen (nicht abgeschirmte
verdrillte Doppelkabel).
2
185/56
Maximumlengte
Maximale Länge des UTP-Videokabels (Fuß/Meter)
6Ω
30 Ω
73/22
Honeywell beveelt het gebruik aan van de volgende NVT video zendontvangers
(apart verkocht via NVT Inc.):
•
NV-212A (500 ft/152 m—26 Ω)**
•
NV-213A/A-M (1000 ft/305 m—52 Ω)**
•
NV-652R, NV-862R of NV-1662R (3000 ft/914 m—163 Ω)**
** De afstanden zijn berekend met gebruik van 24 AWG gevlochten paar draad.
3Ω
20 Ω
45/14
2000/610
18
33 Ω
15 V DC
750/229
250/76
17 Ω
16
AWG
UTP videokabel maximum lengte (voet/meter)
AWG
10 Ω
18
AWG
14 AWG*
40 Ω
5Ω
22
AWG
23 AWG* 18 AWG*
26 Ω
8Ω
24
AWG
* Met koper beklede stalen kern, 95% gevlochten afscherming
3000/914
20
Voeding
RG-11
2000/610
22
2
Instalar directamente numa caixa
eléctrica 4S
Direkte Befestigung an einer 4SAnschlussdose
Figuur 3 illustreert hoe de HEV28P direct op een 4S elektriciteitsdoos
wordt gemonteerd.
A Figura 3 ilustra a montagem da HEV28P directamente numa caixa
eléctrica 4S:
Die Abbildung 3 zeigt, wie das Modell HEV28P direkt an einer 4SAnschlussdose befestigt wird.
Nota
Hinweis
Opmerking De adapterplaat kan gebrukt worden om
onvolmaaktheden in plafond of muur af te dekken
rond de opening van de elektriciteitsdoos. Het
gebruik van de adapterplaat is optioneel.
2.
1.
Fixe a placa adaptadora opcional à caixa eléctrica 4S com os
parafusos apropriados (não fornecidos).
Fixe a base HEV28P com os parafusos para metal nº 8-32 de 3/8
polegadas (x3) fornecidos.
2.
Honeywell Security France
Parc Gutenberg, 13, Voie La Cardon
91120, Palaiseau, France
www.ademco.fr
℡ +33.1.6932.1090
Honeywell Security Italia SpA
Via della Resistenza 53/59, 20090 Buccinasco
Milan, Italy
www.ademco.it
℡ +39.02.457.1791
Honeywell Security Espana
Calle Vivero, 5, 28040
Madrid, Spain
www.security.honeywell.com/es
℡ +34.91.102.5900
Honeywell Security Nederland
Amperestraat 41
1446 TR Purmerend, Netherlands
www.SecurityHouse.nl
℡ +31.299.419.000
Honeywell Security South Africa
Unit 6 Galaxy Park, Galaxy Avenue, Linbro Business Park
P.O. Box 59904, Kengray, 2100, South Africa
www.honeywell.co.za
℡ +27.11.574.2500
Honeywell Security Germany
Großenbaumer Weg 8
40472 Düsseldorf, Germany
www.honeywell-security.de
℡ +49.211.415.090
Honeywell Security Poland
Chmielewskiego 22a, 70-028
Szczecin, Polska
www.ultrak.pl
℡ +48.91.485.40.60
Honeywell Security Czech Republic
Havránkova 33, Brno
Dolní Heršpice, 619 00, Czech Republic
www.olympo.cz
℡ +420.543.558.111
Honeywell Security Slovakia Republic
Vajnorskà 142, 83104 Bratislava
Slovakia
www.olympo.sk
℡ +421.2.444.54.660
Monteermogelijkheden
Monteer direct op een 4S
electriciteitsdoos
A placa adaptadora pode ser utilizada para tapar
imperfeições no tecto ou na parede à volta da abertura
da caixa eléctrica. A utilização da placa adaptadora é
opcional.
Honeywell Security Asia Pacific
Flat A, 16/F, CDW Building, 388 Castle Peak Road
Tsuen Wan, N.T., Hong Kong
www.security.honeywell.com/hk
℡ +852.2405.2323
Opmerking Gebruik uitsluitend punt-tot-punt UTP (onafgeschermd gevlochten
paar) draad.
Montageoptionen
1.
Parafusos de segurança n° 8-32 de 7/
16 polegadas (x3)
Nr. 8-32 x 7/16 Zoll
Sicherungsschrauben (3 St.)
#8-32 x 7/16 inch veiligheidschroeven
(x3)
Mit der Adapterplatte können Fehlerstellen an der
Decke oder Wand um die Anschlussdose herum
abgedeckt werden. Die Verwendung der Adapterplatte
ist optional.
1.
2.
Befestigen Sie die optionale Adapterplatte mit geeigneten
Schrauben (nicht mitgeliefert) an der 4S-Anschlussdose.
Befestigen Sie den HEV28P-Sockel mit den mitgelieferten Nr. 8-32
x 3/8 Zoll Maschinenschrauben (3 St.).
Bevestig de optionele adapterplaat op de 4S elektriciteitsdoos
met geschikte schroeven (niet bijgeleverd).
Bevestig de HEV28P basis met bijgeleverde #8-32 x 3/8 inch
schroeven (x3).
Oppervlaktemontage
Volg Figuur 4 om de HEV28P op een plafond of muur te monteren.
Tampa frontal
Vordere
Abdeckung
Frontplaat
Montagem à superfície
Montage über Putz
Siga as indicações da Figura 4 para montar a HEV28P num tecto ou
parede.
Die HEV28P wird wie in Abbildung 4 dargestellt an einer Decke oder
Wand befestigt.
1.
1.
Para instalações com a placa adaptadora, fixe a orla com os
parafusos nº 8-32 de 7/8 polegadas (x3) de cabeça plana
fornecidos.
Nota
2.
Fixe a base HEV28P com os parafusos para metal nº 8-32 de 3/8
polegadas (x3) fornecidos.
2.
2.
Wenn Sie auf die Adapterplatte verzichten, verwenden
Sie für den Einbau entsprechend geeignete Schrauben
(nicht mitgeliefert).
Figuur 5 illustreert hoe de HEV28P ingebouwd op een 4S
elektriciteitsdoos wordt gemonteerd.
Voor montage met adapterplaat, bevestigt u de HEV28P basis met
bijgeleverde #8-32 x 7/8 inch cilinderkopschroeven (x3).
Wanneer geen gebruik wordt gemaakt van de adapterplaat, gebruikt u
schroeven die geschikt zijn voor uw installatie (niet bijgeleverd).
3
Volgende stappen
1.
3
Passos seguintes
1.
2.
4
3
Instale o cardan. Consulte o Manual de Instalação Rápida do
Cardan fornecido com o cardan (caixa verde).
Instale a objectiva. Consulte o Manual de Instalação Rápida da
Objectiva fornecido com a objectiva (caixa azul).
Nächste Schritte
1.
2.
Installieren Sie den Kardan. Informationen dazu finden Sie in der
Kurzanleitung für Kardaneinbau, die mit dem Kardan mitgeliefert
wird (grüne Schachtel).
Bauen Sie das Objektiv ein. Informationen dazu finden Sie in der
Kurzanleitung für Objektiveinbau, die mit dem Objektiv mitgeliefert
wird (blaue Schachtel).
Fixe a tampa
Fixe a caixa da dome HEV28P à base com três parafusos de segurança
nº 8-32 de 7/16 polegadas (consulte a Figura 6).
A câmara está pronta a funcionar.
Manutenção de rotina
4
Befestigen der Abdeckung
2.
4
Plaats de cardanische ophanging. Zie de Handleiding voor snelle
installatie van de cardanische ophanging geleverd bij de
cardanische ophanging (groene doos).
Plaats de lens. Zie de Handleiding voor snelle installatie van de
lens geleverd bij de lens (blauwe doos).
Bevestig het deksel
Bevestig het HEV28P kapomhulsel op de basis met drie #8-32 x 7/16
inch veiligheidsschroeven (zie Figuur 6).
De camera kan nu werken.
Befestigen Sie das HEV28P-Kuppelgehäuse mit drei Nr. 8-32 x 7/16 Zoll
Sicherungsschrauben am Sockel (siehe Abbildung 6).
Routine-onderhoud
Ihre Kamera ist jetzt einsatzbereit.
Gebruik gewone vloeibare schoonmaakmiddelen om vuil te verwijderen
van de HEV28P kap.
Utilize produtos de limpeza líquidos normais para remover a sujidade
da dome HEV28P.
Routinemäßige Wartung
Atenção
Verwenden Sie normale Flüssigreiniger zum Entfernen von Schmutz
und Verunreinigungen von der HEV28P-Kuppel.
Não utilize produtos ásperos e abrasivos que
podem riscar a dome de policarbonato e reduzir
a visibilidade da câmara.
Bevestig de HEV28P basis met bijgeleverde #8-32 x 3/8 inch
schroeven (x3).
Ingebouwde montage
Befestigen Sie den HEV28P-Sockel mit den mitgelieferten Nr. 8-32
x 3/8 Zoll Maschinenschrauben (3 St.).
Die Abbildung 5 zeigt, wie das Modell HEV28P an der Decke oder Wand
montiert wird. Bei Montage an einer Adapterplatte befestigen Sie den
HEV28P-Sockel mit den mitgelieferten Nr. 8-32 x 7/8 Zoll
Zylinderkopfschrauben (3 St.). Wenn Sie auf die Adapterplatte
verzichten, verwenden Sie für den Einbau entsprechend geeignete
Schrauben (nicht mitgeliefert).
Voor montage met adapterplaat, bevestigt u de rand met
bijgeleverde #8-32 x 7/8 inch cilinderkopschroeven (x3).
Opmerking Wanneer geen gebruik wordt gemaakt van de
adapterplaat, gebruikt u schroeven die geschikt zijn
voor uw installatie (niet bijgeleverd).
Montage unter Putz
A Figura 5 ilustra a montagem da HEV28P encastrada no tecto ou
parede.
Para instalações com a placa adaptadora, fixe a base HEV28P com os
parafusos nº 8-32 de 7/8 polegadas (x3) de cabeça plana fornecidos.
Quando não utilizar a placa adaptadora, use parafusos apropriados
para a instalação (não fornecidos).
Junta
Dichtung
Pakking
1.
Bei Montage an einer Adapterplatte befestigen Sie die Einfassung
mit den mitgelieferten Nr. 8-32 x 7/8 Zoll Zylinderkopfschrauben
(3 St.).
Hinweis
Quando não utilizar a placa adaptadora, use parafusos
apropriados para a instalação (não fornecidos).
Montagem encastrada
Placa de retenção
Halterungsplatte
Houdplaat
660/201
Maximale Länge des Koaxial-Videokabels (Fuß/Meter)
A Honeywell recomenda os seguintes transmissores-receptores de vídeo NVT
(vendidos separadamente pela NVT Inc.):
•
NV-212A (500 pés/152 m—26 Ω)**
•
NV-213A/A-M (1000 pés/305 m—52 Ω)**
•
NV-652R, NV-862R ou NV-1662R (3000 pés/914 m—163 Ω)**
** As distâncias foram calculadas utilizando um fio de Par Entrançado 24 AWG.
Substituição da dome / Auswechseln der Kuppel / Vervanging
van de kap
Parafusos para metal n° 8-32 de 5/
16 polegadas (x3)
Nr. 8-32 x 5/16 Zoll
Maschinenschrauben (3 St.)
#8-32 x 5/16 inch schroeven (x3)
2664/812
* Kupferummantelter Stahlkern, 95% umwickelte Abschirmung
Base HEV28P
HEV28P-Sockel
HEV28P basis
Dome de policarbonato
Polycarboat-Kuppel
Polycarbonaat kap
16
AWG
Maximale Länge
Instalação da tampa da caixa / Einbau der Gehäuseabdeckung /
Plaatsing van omhulselkap
Parafusos de segurança n° 8-32 de
7/16 polegadas (x3)
Nr. 8-32 x 7/16 Zoll
Sicherungsschrauben (3 St.)
#8-32 x 7/16 inch
veiligheidschroeven (x3)
18
AWG
Comprimento máximo do cabo de vídeo UTP (pés/metros)
2
Figure 7
22
AWG
RG-59
24
Caixa da dome
Kuppel
Gehäuse
Kap omhulsel
295/90
24
AWG
Honeywell Security Australia Pty Ltd.
Unit 5, Riverside Centre, 24-28 River Road West
Parramatta, NSW 2150, Australia
www.ademco.com.au
℡ +61.2.8837.9300
Draaddiameter
AWG (Amerikanische Norm für Drahtquerschnitte)
* Núcleo de aço revestido a cobre, blindagem 95% entrançada
Nota
Figure 6
Drahtquerschnitt
Honeywell Video Systems (Head Office)
2700 Blankenbaker Pkwy, Suite 150
Louisville, KY 40299, USA
www.honeywellvideo.com
℡ +1.800.796.2288
Honeywell Video Systems UK Ltd.
Aston Fields Road, Whitehouse Ind Est
Runcorn, Cheshire, WA7 3DL, UK
www.security.honeywell.com
℡ +44.1928.754.000
Kabelrichtlijnen
Maximumlengte voedingkabel (voeten/meters)
Camera's met AC/DC voeding
Stromversorgung
Tipo de cabo
250/76
Opmerking Voor veilige installaties moeten aan het oppervlak
gemonteerde kabels beschermd zijn met een plastic
of metalen kabelafdekking.
Für eine sichere Installation sollten über Putz verlegte
Kabel mit einer Abdeckung aus Kunststoff oder Metall
geschützt werden.
Richtlinien für Kabel
Nota
Os cálculos baseiam-se numa fonte de alimentação linear não regulada
que seria o pior caso. A utilização de uma fonte de alimentação regulada ou
comutada poderá aumentar a distância do cabo. A Honeywell recomenda que
seja utilizada uma fonte de alimentação com Certificação CAS / Classe 2 de UL
para assegurar a conformidade com as normas de segurança eléctrica.
AWG
Volg Figuur 2 voor de kabelaansluiting.
Maximale Länge des Stromversorgungskabels (Fuß/Meter)
Kameras mit Wechselstrom-/Gleichstrom-Versorgung
Fonte de
alimentação
Comprimento máximo
Het gebruik van CSA Gecertificeerde/UL geregistreerde
Klasse 2 voeding is vereist om zeker te zijn van conformiteit
met de elektrische veiligheidsnormen.
Der Anschluss der Leitungen erfolgt gemäß Abbildung 2.
Comprimento máximo do cabo de vídeo coaxial (pés/metros)
Base HEV28P
HEV28P-Sockel
HEV28P basis
Kabelaansluitingen
WAARSCHUWING!
Die Verwendung einer CSA-zertifizierten/UL-gelisteten
Klasse-2-Stromversorgung ist erforderlich, um die Einhaltung
der elektrischen Sicherheitsstandards zu garantieren.
Para instalações seguras, os cabos montados à
superfície devem ser protegidos por coberturas
plásticas ou metálicas.
Espessura do fio
Fios eléctricos
cablagem
Leitung, Kabel
Bedrading,
bekabeling
1
ACHTUNG!
Comprimento máximo do cabo de alimentação (pés/metros)
Câmaras com fontes de alimentação CA/CC
Instalação de montagem à superficie / Einbau über Putz /
Oppervlaktemontage
De HEV28P is bedoeld voor montage op het oppervlak van een muur of
plafond. Het is weerbestendig afgedicht voor binnen en buiten. De
HEV28P installatiekit wordt geleverd met een adapterplaat voor zeer
flexibele bevestigingsmogelijkheden (zie Figuur 1).
Leitungsanschlüsse
Consulte a Figura 2 que indica as ligações dos fios eléctricos.
Base HEV28P
HEV28P-Sockel
HEV28P basis
Installatie-overzicht
Einbau - Überblick
A utilização de uma fonte de alimentação com Certificação
CSA / Classe 2 de UL é obrigatória para assegurar a
conformidade com as normas de segurança eléctricas.
Nota
Pak alles uit. Controleer of u alle onderdelen hebt ontvangen die op het
orderformulier en op de pakbon worden vermeld. De HEV28P
verpakking moet behalve deze Handleiding voor snelle installatie
omvatten:
•
Een HEV28P omhulsel
•
Een HEV28P hardware kit
•
Een Productgarantiekaart
Neem wanneer er onderdelen ontbreken of zijn beschadigd, contact op
met de leverancier waar u de camera hebt aangeschaft of neem contact
op met de klantenservice van Honeywell.
Packen Sie alles aus. Überprüfen Sie, ob die erhaltenen Artikel mit dem
Bestellformular und dem Packzettel übereinstimmen. Die HEV28PVerpackung sollte außer dieser Kurzanleitung für den Einbau Folgendes
enthalten:
•
Ein HEV28P-Gehäuse
•
Ein HEV28P-Hardwaremontagesatz
•
Eine Produktgarantiekarte
Bei fehlenden oder beschädigten Teilen wenden Sie sich bitte an den
Händler, von dem Sie die Kamera erworben haben, oder rufen Sie die
Kundenbetreuung von Honeywell an.
Ligações de fios eléctricos
AVISO!
Caixa eléctrica 4S (não
fornecida)
4S-Anschlussdose (nicht
mitgeliefert)
4S elektriciteitsdoos (niet
bijgeleverd)
DIT SYMBOOL BETEKENT DAT ER
BELANGRIJKE BEDIENINGS- EN
ONDERHOUSINSTRUCTIES BIJ
DIT APPARAAT AANWEZIG ZIJN.
LET OP: VERWIJDER DE KAP NIET, OM DE KANS OP
ELEKTRISCHE SCHOKKEN TE VERKLEINEN. DIT
APPARAAT BEVAT GEEN ONDERELEN DIE U ZELF
KUNT REPAREREN. LAAT REPARATIES UITVOEREN
DOOR ERKEND ONDERHOUDSPERSONEEL.
Bevor Sie anfangen
A HEV28P foi concebida para ser montada à superfície numa parede ou
tecto. Está vedada contra as condições atmosféricas para utilização no
interior ou exterior. O kit de instalação da câmara HEV28P (consulte a
Figura 1) contém uma placa adaptadora que fornece as opções de
montagem mais flexíveis.
Alimentação: Pino de contacto
macho de 2,1 mm
Strom: 2,1 mm Klinke mittig Pin
Voeding: 2,1 mm mannelijke
stekkar centrale pin
DIT SYMBOOL BETEKENT DAT ER
IN DIT APPARAAT GEVAARLIJKE
SPANNING AANWEZIG IS, MET
HET RISICO VAN ELEKTRISCHE
SCHOKKEN.
LET OP
GEVAAR VOOR ELEKTRISCHE
SCHOKKEN
NET OPENEN
Voordat u begint
Orientações gerais para os cabos
Figure 4
Dit apparaat moet worden geïnstalleerd en onderhouden door
bevoegde technici, zodat aan alle plaatselijke voorschriften wordt
voldaan en uw garantie geldig blijft.
DIESES SYMBOL WEIST AUF
WICHTIGE BETRIEBS- UND
WARTUNGSANWEISUNGEN HIN,
DIE IM LIEFERUMFANG DIESES
GERÄTS ENTHALTEN SIND.
VORSICHT: UM DAS RISIKO EINES STROMSCHLAGES ZU
REDUZIEREN, ENTFERNEN SIE NIEMALS DIE VORDERE
ODER RÜCKSEITIGE ABDECKUNG. ES BEFINDEN SICH
KEINE BENUTZERRELEVANTEN SERVICETEILE UNTER
DER ABDECKUNG. WENDEN SIE SICH FÜR
SERVICEFÄLLE AN QUALIFIZIERTES
SERVICEPERSONAL.
Plaats de behuizing. Volg de aanwijzingen in deze handleiding op.
Plaats de cardanische ophanging. Zie de Handleiding voor snelle
installatie van de cardanische ophanging geleverd bij de
cardanische ophanging (groene doos).
Plaats de lens. Zie de Handleiding voor snelle installatie van de
lens geleverd bij de lens (blauwe doos).
Plaats het deksel van de behuizing. Volg de aanwijzingen in deze
handleiding op.
Contact Information
L’Information de Contact
Información del Contacto
Le Informazioni del Contatto
Informação do Contato
Kontact Informationen
Contact Informatie
Belangrijke veiligheidsmaatregelen
DIESES SYMBOL ZEIGT AN, DASS
DIESES GERÄT GEFÄHRLICHE
SPANNUNG VERBUNDEN MIT
DER GEFAHR EINES
STROMSCHLAGS ENTHÄHLT.
VORSICHT
Retire todos os itens da embalagem. Verifique se os itens recebidos
correspondem à lista da nota de encomenda e da folha da embalagem.
A embalagem da câmara HEV28P deve incluir, para além deste Manual
de Instalação Rápida:
•
Uma caixa HEV28P
•
Um kit de hardware HEV28P
•
Um Postal de Garantia do Produto
Se algumas peças estiverem em falta ou danificadas, contacte o agente
ao qual adquiriu a câmara ou contacte o Serviço de Apoio ao Cliente da
Honeywell.
Cabos UTP / UTP-Kabel (unabgeschirmte
verdrillte Zwillingskabel) / UTP kabels
Instalação da caixa eléctrica 4S / Einbau der 4S-Anschlussdose /
Installatie van de 4S elektriciteitsdoos
4.
Einbau und Wartung sollten durch qualifizierte Techniker erfolgen,
damit alle örtlichen Vorschriften eingehalten werden und Ihre Garantie
bestehen bleibt.
Perspectiva geral da instalação
Vermelho +
Rot +
Rood +
3.
Antes de começar
Ligação de fios eléctricos / Leitungsanschluss / Kabelaansluiting
Cabos Coaxiais / Koaxialkabel /
Coaxiale kabels
Bauen Sie das Gehäuse ein. Folgen Sie den Anweisungen in
dieser Anleitung.
Installieren Sie den Kardan. Informationen dazu finden Sie in der
Kurzanleitung für Kardaneinbau, die mit dem Kardan mitgeliefert
wird (grüne Schachtel).
Bauen Sie das Objektiv ein. Informationen dazu finden Sie in der
Kurzanleitung für Objektiveinbau, die mit dem Objektiv mitgeliefert
wird (blaue Schachtel).
Bauen Sie die Gehäuseabdeckung ein. Folgen Sie den
Anweisungen in dieser Anleitung.
Wichtige Sicherheitsvorkehrungen
ESTE SÍMBOLO INDICA QUE
EXISTE DENTRO DESTA
UNIDADE VOLTAGEM PERIGOSA
QUE PODERÁ CAUSAR
CHOQUES ELÉCTRICOS.
CUIDADO
Caixa da dome HEV28P
HEV28PKuppelgehäuse
HEV28P kapomhulsel
Figure 2
Aviso importante
Base HEV28P
HEV28P-Sockel
HEV28P basis
Nederlands
Deutsch
WAARSCHUWING!Gebruik geen agressieve of schurende
schoonmaakmiddelen die de polycarbonate kap
kunnen krassen en het zicht voor de camera kunnen
verminderen.
Als het camerazicht wordt belemmerd door krassen, verwijder dan de
voorplaat en draai de kap tot een krasvrij gedeelte.
Se a vista da câmara estiver obstruída por riscos, remova a placa da
frente e rode-a para encontrar uma parte da dome que não está
riscada.
Vorsicht Verwenden Sie keine groben oder schmirgelnden
Reinigungsmittel, die die Polycarbonat-Kuppel
zerkratzen können und somit das Sehvermögen der
Kamera verringern.
Substituição da dome
Wenn die Kamerasicht durch Kratzer behindert wird, müssen Sie die
vordere Platte entfernen und die Kuppel drehen, bis Sie eine
unzerkratzte Stelle finden.
Als de poycarbonaat kap onbruikbaar is geworden door
beschadigingen of krassen, neem dan contact op met uw dealer of
verkoper om een vervangende kap te bestellen. Vervangen van een
HEV28P kap (zie Figuur 7):
Auswechseln der Kuppel
1.
Se a dome de policarbonato ficar danificada ou riscada
impossibilitando a respectiva utilização, contacte o distribuidor ou
agente de vendas para encomendar uma dome de substituição. Para
substituir a dome da HEV28P (consulte a Figura 7):
1.
2.
3.
4.
5.
Utilize a chave de segurança sextavada (fornecida) para
desapertar os três parafusos de segurança nº 8-32 de 7/16
polegadas que fixam a tampa da HEV28P à base.
Utilize uma chave de fendas em cruz para remover os três
parafusos para metal nº 8-32 de 5/16 polegadas que fixam a
placa de retenção da dome à tampa da frente.
Remova a dome danificada e substitua-a por uma nova.
Utilize uma chave de fendas e cruz para fixar a placa de retenção
da dome à placa frontal da HEV28P com os parafusos removidos
no passo 2.
Utilize a chave de segurança sextavada para fixar a tampa da
HEV28P à base.
Wenn die Polycarbonat-Kuppel so beschädigt oder zerkratzt ist, dass
sie nicht mehr verwendet werden kann, wenden Sie sich an Ihren
Lieferanten oder Händler, um eine Ersatzkuppel zu bestellen. So wird
die HEV28P-Kuppel ausgewechselt (siehe Abbildung 7):
1.
2.
3.
4.
5.
Lösen Sie mit dem mitgelieferten Sechskantschlüssel die drei Nr.
8-32 x 7/16 Zoll Sicherungsschrauben, mit denen der HEV28PDeckel am Sockel befestigt ist.
Entfernen Sie mit einem Kreuzschlitzschraubendreher die drei Nr.
8-32 x 5/16 Zoll Maschinenschrauben, mit denen die
Kuppelhalterungsplatte an der vorderen Abdeckung befestigt ist.
Entfernen Sie die beschädigte Kuppel, und ersetzen Sie sie mit
einer neuen Kuppel.
Befestigen Sie die Kuppelhalterungsplatte mit einem
Kreuzschlitzschraubendreher an der vorderen Platte der HEV28P.
Verwenden Sie dabei die Schrauben, die Sie in Schritt 2 entfernt
haben.
Befestigen Sie mit dem Sechskantschlüssel den HF28P-Deckel
am Sockel.
Vervanging van de kap
2.
3.
4.
5.
Gebruik de (bijgeleverde) zeskant veiligheidssleutel om de drie
#8-32 x 7/16 inch veiligheidsschroeven los te draaien die het
HEV28P deksel op de basis bevestigen.
Gebruik een kruiskopschroevendraaier om de drie #8-32 x 5/16
inch schroeven te verwijderen die de kaphouder op de voorplaat
bevestigen.
Verwijder de beschadigde kap en vervang deze door een nieuwe
kap.
Gebruik een kruiskopschroevendraaier om de kaphouder te
bevestigen op de HEV28P voorplaat met de schroeven die u hebt
verwijderd in stap 2.
Gebruik de zeskant veiligheidssleutel om het HEV28P deksel op
de basis te bevestigen.
Video Systems
www.honeywellvideo.com
+1.800.796.CCTV
© 2005 Honeywell International Inc.
Document 900.0291 Rev 1.02 09/05
Specifications are subject to change without notice.
Especificaciones pueden cambiar sin aviso.
Caractéristiques techniques sujettes à changement sans prévais.
Specifiche tecniche soggette a modifica senza preavviso.
Especificações sujeitas a alteração sem aviso prévio.
Spezifikationen unterliegen Änderungsvorbehalt ohne vorherige
Ankündigung.
Specificaties kunnen zonder kennisgeving worden gewijzigd.
Imperial conversions are approximate.
La conversin des unités impériales est approximative.
Las conversiones a unidades imperiales son aproximadas.
Le conversioni in unita di misura del sistema metrico (sistema imperiale)
sono approssimative.
As conversões das medidas imperiais são aproximadas.
Umrechnungen in das metrische System sind Näherungen.
Omrekeningen van Engelse maten zijn bij benadering.

Documents pareils

HEC14 Housing Quick Install Guide

HEC14 Housing Quick Install Guide Remarque Les longueurs ont été calculées en utilisant un fil à paire torsadée de calibre 24 AWG.Nous vous recommandons de mesurer la longueur du fil afin de vous assurer que le système n’excède pas...

Plus en détail