Lumec New Westminster Globe

LUMEC NEW WESTMINSTER RETROFIT
DECORATIVE LED RETROFIT LUMINAIRE
Includes: XRAAF Series
INSTALLATION INSTRUCTIONS
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
DANGER – RISK OF SHOCK – DISCONNECT POWER BEFORE INSTALLATION
DANGER – RISQUE DE CHOC – COUPER L’ALIMENTATION AVANT L’INSTALLATION
2. This LED retrofit product is UL Classified for use with New Westminster Series, manufactured by Lumec only. DO NOT
install into any other manufacturer’s luminaire. To maintain existing Luminaires’ UL listing, the LED retrofit kit must be
UL Classified for use with the manufacturer and model of existing luminaire. Consult CREE Customer support to see if
other luminaires are classified to be used with this LED Retrofit kit.
Ce produit retrofit LED est classifié UL pour une utilisation avec la série New Westminster, fabriqué par Lumed seulement. Ne
pas installez ce retrofit LED dans le luminaire de tout autre fabricant. Pour maintenir la qualification UL des Luminaires
existants, le kit LED retrofit doit être classifié UL pour une utilisation avec le fabricant et le modèle de luminaire existant.
Consulter CREE Support Clientèle pour voir si les autres luminaires peuvent être utilisés avec ce retrofit LED.
3. WARNING – Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical
systems. If not qualified, do not attempt installation. Product must be installed in accordance with NEC or your local
electrical code. If you are not familiar with these codes and requirements, contact a qualified electrician.
ATTENTION- Risque d'incendie ou de choc électrique. L’installation du kit retrofit LED exige la connaissance des systèmes
électriques pour luminaires. Si non qualifié, ne tentez pas d'installation. Ce produit doit être installé conformément à NEC ou
votre code électrique local. Si vous n'êtes pas familier avec ces codes et ces exigences, veuillez contacter un électricien
qualifié.
4. WARNING – Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for
installation of the LED retrofit kit. Check for enclosed wiring and components.
ATTENTION - Risque d'incendie ou de choc électrique. Câblage électriques peuvent être endommagés lors du perçage pour
l'installation du kit retrofit LED. Vérifier les fils et composants.
5. WARNING – Risk of fire or electric shock. Check the existing wiring for damage before installing retrofit kit. Do not
install if existing wires are damaged.
ATTENTION- Risque d'incendie ou de choc électrique. Vérifiez si le câblage existant n’est pas endommagé avant l'installation
du kit retrofit LED. Ne pas installer si des fils sont endommagés.
6. WARNING – To prevent wiring damage or abrasion, do not expose wires to the edge of sheet metal or any other sharp
objects.
ATTENTION - Pour éviter les dégâts de câblage par l'abrasion, ne pas mettre en contact les fils électriques avec des bords de
tôle ou d'autres objets pointus.
7. WARNING – Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and
dimensions shown in the photographs and/or drawings.
ATTENTION - Risque d'incendie ou de choc électrique. Installez ce kit seulement dans les luminaires qui ont les
caractéristiques de construction et les dimensions dans les photographies ou les dessins de la page suivante.
8. Do not make or alter any holes in a wiring enclosure or electrical components during the kit installation.
Ne pas modifier ou faire de trous dans une boite de câblage ou compartiment électrique lors de l'installation du kit.
9. Ensure that the existing luminaire is installed according to original manufacturer’s specification.
S'assurer que les luminaires sont installés selon les spécifications du fabricant.
10. Only the holes indicated in the photographs or drawings may be made or altered as a result of the kit installation. Do
not leave any other holes open in a wiring enclosure or electrical component.
Seulement les trous indiqués dans les photographies ou les dessins peuvent être faits ou altérés pour l’installation du kit retrofit
LED. Ne laissez aucun trou ouvert dans le compartiment électrique.
11. The retrofit kit contains a universal LED driver and can be operated at voltages of 120-277V.
Le kit de rénovation contient une alimentation universelle et peut fonctionner à des tensions de 120-277V.
12. Once the Retrofit kit is installed, the luminaire can no longer accept HID lamps and shall not be converted back to an
HID luminaire.
Une fois le kit retrofit LED installé, l'appareil peut ne plus accepter les lampes HID et ne pourra pas être retransformé en
luminaire HID.
1.
CAUTION: WHEN HANDLING LEDS

DO NOT CUT PROTECTIVE WRAP

AVOID TOUCHING OPTICS

INSTALL KIT IN FIXTURE THEN REMOVE
PROTECTIVE WRAP BEFORE ENERGIZING
Page 1 of 5
LIST OF SUPPLIED COMPONENTS
1. XRA Series Driver Assembly
2. XRA Series LED Module Assembly.
3. (1) Flat Washer
4. (1) Rotation Stop
5.
(1) Beveled Washer
6.
7.
(1) Nut
LED Module Assembly Mounting Bracket Assembly
CI370X06R0
RETROFIT FIXTURE INSTALLATION
NOTE: Consult your local authority regarding disposal or
recycling of removed ballast, capacitor and lamp.
FIGURE 4
1. Disconnect power to fixture.
2. Verify the existing luminaire model. See Figure 1.
FIGURE 1
7.
Remove the existing socket by removing the screws on
the inside of the ballast enclosure and dispose of properly.
See Figure 5.
FIGURE 5
3.
Rotate the plastic globe and separate the globe from the
housing by carefully lifting it straight up over the lamp and
glass refractor. See Figure 2.
FIGURE 2
8.
4.
Loosen the screws in the key-hole slots that secure the
ballast enclosure and the glass refractor to the housing
and lift it up to separate it from the ballast assembly. See
Figure 3.
Remove the ballast assembly by loosening the screws in
the key-hole slots that secure the ballast enclosure to the
housing and lift it up to separate it from the housing and
dispose of properly. See Figure 6.
FIGURE 6
FIGURE 3
9.
5.
6.
Remove the lamp and dispose of properly.
Separate the glass refractor from the ballast enclosure by
removing the 3 screws and set aside. See Figure 4.
Page 2 of 5
Insert the LED Driver Assembly by lowering it in to the
housing and rotate until the existing screws fit into the
notches on the LED Driver Assembly Plate. Retighten the
screws. See FIGURE 7.
CI370X06R0
FIGURE 7
FIGURE 10
10. The Mounting Bracket Assembly must be mounted to the
existing refractor. See Figure 8.
14. To secure the refractor to the LED Assembly, stand the
LED assembly with the wires pointing up and lower the
refractor over the post. Line up the holes in the mounting
feet with the screw holes in each corner of the triangular
extrusion and secure with the provided screws. See
Figure 11.
FIGURE 8
FIGURE 11
11. Begin by turning the refractor upside down and hold the
flat ring on the inside of the refractor. Then place the ring
with mounting feet on the outside of the glass and hold
them in place sandwiching the glass between the rings.
See Figure 9.
FIGURE 9
15. Secure the supplied rotation stop and nylon washer to the
nipple on the bottom of the LED Assembly post as shown
in Figure 12.
FIGURE 12
12. Line up the screw holes on the two rings and secure with
the supplied screws.
13. Carefully remove the red plastic protective wrap form the
LEDs by peeling it back by the label and avoid touching
the LEDs. See Figure 10.
Page 3 of 5
CI370X06R0
16. To prepare the LED Driver Assembly enclosure, line up
the provided aluminum plate with the appropriate
mounting holes. See Figure 12.
FIGURE 15
FIGURE 12
17. Secure to the top of the housing with the provided screws.
See Figure 13.
FIGURE 13
20. See the Electrical Connections sections to wire the
luminaire.
21. Connect the wire harness from the LED Module Assembly
and the LED Driver Assembly.
22. Once electrical connections are made, lower the existing
driver enclosure over the installed LED Driver Assembly.
Using the key-hole slots secure the assembly and tighten
the existing screws. See Figure 16.
FIGURE 16
18. Place the LED Driver Assembly over the nipple of the LED
Module Assembly as shown in Figure 14.
FIGURE 14
23. Attach the provided rubber ring over the edge of the glass
refractor.
24. Carefully replace the globe over the Retrofit Assembly and
re-tighten the bolts that were loosened in Step 3.
25. Reconnect power to the fixture.
19. Secure using the supplied flat washer, beveled washer
and nut as shown in Figure 15.
Page 4 of 5
CI370X06R0
ELECTRICAL CONNECTIONS
FIELD ADJUSTABLE DIMMING
NOTE: Ground connection should include previous luminaire
ground as well as ground from retrofit panel. Verify that the
supply voltage is within the fixture’s voltage rating.
NOTE: This luminaire is provided with field adjustable
dimming. Luminaires leave the factory adjusted to the
maximum setting which is Position 9 as shown in Figure 10.
1.
For 120-277V applications make the following Electrical
Connections to the terminal block located on the side of
the Retrofit LED Driver Assembly:
a. Connect the black lead to the voltage supply lead
b. Connect the white lead to the neutral supply lead
c. Connect the green or green/yellow ground lead to
the supply ground lead
2.
If Dimming is an option, make the following additional
connections using Class 1 wire:
a. Connect the violet dimming positive lead to the
supply dimming positive lead.
b. Connect the grey dimming negative lead to the
supply dimming negative lead
FIGURE 10
3.
BLACK
LINE – BLACK
GREEN
GROUND – GREEN
WHITE
NEUTRAL – WHITE
VIOLET
DIM (+) – VIOLET
GREY
DIM (-) - GREY
1.
2.
(DIMMING OPTIONAL)
SUPPLY WIRING
120-277V STANDARD FIXTURE WIRING
Locate the luminaires electrical label and verify the
maximum wattage available.
Establish the desired wattage on the following table and
turn the switch to the correlating position.
65-69W
Position
Input Power Multiplier
9
1.00
8
0.92
For 208/240/480V applications, make the following
Electrical Connections to the terminal block located on
the side of the Retrofit LED Driver Assembly:
a. Connect L2 (Hot) supply lead to the black lead.
b. Connect L1 (Hot) supply lead to the white lead
c. Connect the green or green/yellow ground lead to
the supply ground lead
7
0.88
6
0.81
5
0.77
4
0.73
3
0.67
If Dimming is an option, make the following additional
connections using Class 1 wire:
d. Connect the violet dimming positive lead to the
supply dimming positive lead.
e. Connect the grey dimming negative lead to the
supply dimming negative lead
2
0.60
1
0.49
208/240/480V
LINE (L2)
LINE – BLACK
GROUND
GROUND – GREEN
LINE (L1)
NEUTRAL – WHITE
VIOLET
DIM (+) – VIOLET
GREY
DIM (-) - GREY
Page 5 of 5
(DIMMING OPTIONAL)
SUPPLY WIRING
208/240/480V PHASE TO PHASE FIXTURE WIRING
CI370X06R0