Accessories: Dimensioned drawing Electrical connection CSL 710

Accessories: Dimensioned drawing Electrical connection CSL 710

CSL 710
Switching light curtains
en 03-2016/05 50128826
Dimensioned drawing
7m
18 - 30 V
DC




We reserve the right to make changes • DS_CSL710_en_50128826.fm
Switching light curtain
Beam spacings 5 / 10 / 20 / 40 mm
Integrated system controller
Block evaluation of 8 beam areas and
4 blanking areas
 Display in 5 languages for fast alignment,
configuration and diagnosis
 4 configurable switching outputs
 IO-Link interface
A
B
C
D
E
F
G
L
R
T
Y
Beam spacing (see tables)
Measurement field length
Power In/Out
Connection to transmitter
Connection to receiver
M6 thread
Fastening groove
Profile length
Receiver
Transmitter
Beam spacing 5mm:
Beam spacing 10/20/40mm:
Y = 2.5mm
Y = 5mm
Electrical connection
IP 65
IEC 60947...
IEC 60947...
Accessories:
(available separately)
 Mounting brackets/sliding blocks
 Complete mounting bracket sets, incl. 360°
rotatable models or variants with vibration
dampers
 Ready-made connection and interconnection cables
 PC configuration software
Leuze electronic GmbH + Co. KG
[email protected] • www.leuze.com
In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0
CSL 710 - 03
CSL 710
Technical data
Tables
Optical data
Typ. operating range limit 1)
Operating range 2)
Meas. field length 3)
Beam spacing 3)
Resolution
Light source
Wavelength
0.2 … 9m (with beam spacing ≥ 10mm)
0.1 … 4.5m (with 5mm beam spacing)
0.3 … 7m (with beam spacing ≥ 10mm)
0.1 … 3.5m (with 5mm beam spacing)
150mm … 2960mm in increments of 80/160mm
5mm, 10mm, 20mm, 40mm
See technical documentation
LED (modulated light)
940nm (infrared light)
Timing
Response time per beam 4)
Delay before start-up
30μs
≤ 1.5s
Electrical data
Operating voltage UB 5)
Residual ripple
Open-circuit current
18 … 30VDC (incl. residual ripple)
≤ 15% of UB
See technical documentation
Interfaces
Inputs/outputs
Switching output current
Signal voltage active/not active
Activation delay
Input resistance
Digital interfaces
4 pins can be configured as input or output
Max. 100mA
≥ 8V/≤ 2V or not connected
≤ 1ms
Approx. 6kΩ
IO-Link
Indicators
Receiver:
Green LED continuous light
Green/yellow LED flashing
Yellow LED continuous light
Yellow LED off
Transmitter:
Green LED continuous light
(or flashing in sync with the
measurement)
Green LED off
Display
Ready
System or teach error
(see technical documentation)
Light path free, with function reserve
Light path interrupted, object detected
Ready
No communication with the receiver
Basic settings and status information
Mechanical data
Housing
Optics cover
Connection type
Fastening
Continuous-cast aluminum
Plastic
M12 connectors
Lateral sliding block or face-mounted corner bracket
Environmental data/standards
Ambient temp. (operation/storage)
Protective circuit 6)
VDE safety class
Degree of protection
Light source
Standards applied
Certifications
1)
2)
3)
4)
5)
6)
-30°C … +60°C/-40°C … +70°C
1, 2, 3
III
IP 65
Exempt group (in acc. with EN 62471)
IEC 60947-5-2 7)
UL 508, CSA C22.2 No.14 5) 8)
Typ. operating range limit: min./max. attainable range without function reserve in parallel-beam operation
Operating range: recommended range with function reserve in parallel-beam operation
Measurement field lengths and beam spacings specified in fixed rasters, see ordering table
Cycle time = number of beams x 0.03 ms + 0.4 ms. The minimum cycle time is 1 ms.
For UL applications: use is permitted exclusively in Class 2 circuits according to NEC
1=transient protection, 2=polarity reversal protection, 3=short circuit protection for all outputs,
must be provided with external protective circuit for inductive loads!
7) Electromagnetic compatibility: This is a Class A product.
In a domestic environment this product may cause radio interference, in which case the operator may be
required to take adequate measures.
8) These proximity switches shall be used with UL Listed Cable assemblies rated 30V, 0.5A min,
in the field installation, or equivalent (categories: CYJV/CYJV7 or PVVA/PVVA7)
Profile length L [mm]
Measurement field length B
[mm]
At beam spacing A [mm]
5
10
20
40
160 160 150
–
240
–
–
–
320 320 310 290
400
–
–
–
480 480 470
–
560
–
–
–
640 640 630 610
720
–
–
–
800 800 790
–
880
–
–
–
960 960 950 930
1040
–
–
–
1120 1120 1110
–
1200
–
–
–
1280 1280 1270 1250
1360
–
–
–
1440 1440 1430
–
1520
–
–
–
1600 1600 1590 1570
1680
–
–
–
1760 1760 1750
–
1840
–
–
–
1920 1920 1910 1890
2000
–
–
–
2080 2080 2070
–
2160
–
–
–
2240 2240 2230 2210
2320
–
–
–
2400 2400 2390
–
2480
–
–
–
2560 2560 2550 2530
2640
–
–
–
2720 2720 2710
–
2800
–
–
–
2880 2880 2870 2850
2960
–
–
–
168
248
328
408
488
568
648
728
808
888
968
1048
1128
1208
1288
1368
1448
1528
1608
1688
1768
1848
1928
2008
2088
2168
2248
2328
2408
2488
2568
2648
2728
2808
2888
2968
Notes
Observe intended use!
 This product is not a safety sensor
and is not intended as personnel
protection.
 The product may only be put into
operation by competent persons.
 Only use the product in accordance with its intended use.
 The functional earth must
be connected to the sliding block connections.
CSL 710 - 03
2016/05
CSL 710
Switching light curtains
Part number code
C S L 7 1 0 - T 0 5 - 1 9 2 0 . A
- M 1 2
C S L 7 1 0 - R 0 5 - 1 9 2 0 . A / L - M 1 2
Operating principle
CSL
Switching light curtain
Series
710
710 series, 7 m range, cycle time 30μs per beam, display
Function
T
Transmitter
R
Receiver
Beam spacing
05
5mm
10
10mm
20
20mm
40
40mm
Measurement field length
xxxx
Measurement field length [mm], dependent on beam spacing,
For values see "Tables" on Page 2
Equipment
A
Plug outlet axial
Interface
L
IO-Link
Electrical connection
M12
M12 connector
Leuze electronic GmbH + Co. KG
[email protected] • www.leuze.com
In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0
CSL 710 - 03
CSL 710
Order guide
Designation
Transmitter (see type code)
CSL710-T…
Receiver (see type code)
CSL710-R…
Part no.
Accessories
Mounting brackets
4 sliding blocks
Bracket set 360° (consisting of 2 x BT 360°)
L-angle bracket set (consisting of 2 x BT-L)
Z-angle bracket set (consisting of 2 x BT-Z)
Mounting clamp set for mounting in device columns (consisting of 2 x BT-P40)
2 mounting brackets, 70mm long, swiveling with vibration damper, incl. 4 screws and 4 sliding blocks
2 mounting brackets, 270mm long, swiveling with vibration damper, incl. 4 screws and 4 sliding blocks
2 swiveling mounting brackets with fastening screws, swiveling from -8° to +8°
2 swiveling mounting brackets with fastening screws, swiveling from -8° to +8°, with vibration damping
BT-4NC
BT-2R1
BT-2L
BT-2Z
BT-2P40
BT-2SSD
BT-2SSD-270
BT-2SB10
BT-2SB10-S
425725
429046
429056
429057
424417
429058
429049
424422
424423
Connection cables with M12 connector, 8-pin socket - open cable end
Connection cable 2m, PUR sheathing
Connection cable 5m, PUR sheathing
Connection cable 10m, PUR sheathing
K-D M12A-8P-2m-PUR
K-D M12A-8P-5m-PUR
K-D M12A-8P-10m-PUR
50104591
50104590
50106882
Interconnection cables between transmitter and receiver
Interconnection cable 1m, PUR sheathing
Interconnection cable 2m, PUR sheathing
Interconnection cable 5m, PUR sheathing
Interconnection cable 10m, PUR sheathing
Interconnection cable 20m, PUR sheathing
KDS DN-M12-5A-M12-5A-P3-010
KDS DN-M12-5A-M12-5A-P3-020
KDS DN-M12-5A-M12-5A-P3-050
KDS DN-M12-5A-M12-5A-P3-100
KDS DN-M12-5A-M12-5A-P3-200
50129779
50129780
50129781
50129782
50129783
SET MD12-US2-IL1.1 + accessories
K-DS M12A-8P-4P-2m-L-PUR
K-DS M12A-8P-4P-5m-L-PUR
50121098
50120999
50121000
Connection cables
IO-Link accessories
Programming set
IO-Link USB master V2.0 + cable + power supply unit
Interconnection cable CSL 710 to IO-Link master, 2m, 8-pin socket / 5-pin plug
Interconnection cable CSL 710 to IO-Link master, 5m, 8-pin socket / 5-pin plug
CSL 710 - 03
2016/05