Life Fitness - AI TR TR4000 M051-00K20-C078

TREADMILL
INSTALLATION INSTRUCTIONS
Congratulations...
and welcome to the world of
and the Life Fitness 4000 treadmill.
The following Parts Identification Listing and the step by step installation
procedures have been assembled to make the set-up of this aerobic trainer as
quick and easy as possible.
Please take special note of the following important points prior to choosing a
location and beginning assembly of the treadmill…
IMPORTANT SAFETY INSTRUCTIONS !
?
DO NOT position the rear of the treadmill within 6 feet ( 2 meter ) of the nearest obstruction. The sides of the
treadmill should maintain a minimum clearance of 8 inches ( 21 cm ) from the nearest treadmill or other
obstruction.
?
DO NOT locate the treadmill within 30 inches ( 76 cm ) of a television set.
?
DO NOT locate the treadmill outdoors, near swimming pools, or in areas of high humidity.
?
DO position the POWER CORD parallel to, but away from, the front of the treadmill.
?
DO verify the contents of the delivery carton against the accompanying parts listing prior to setting the cartons
and shipping material aside. If any parts are missing, contact Life Fitness Customer Support Services at the
number listed on the back page of this installation instruction booklet. Save the shipping cartons in case of
return.
?
DO read the entire Operation Manual prior to attempting to operate this machine as this is essential for proper
use. The Manual explains how to properly use the treadmill and helps you to design an aerobic workout
tailored to your personal fitness needs or requirements.
?
Ne placez pas l'arrière du tapis roulant à moins de 6 pieds (2 mètres) de l'obstruction la plus proche. Les côtés
du tapis roulant devraient mettre à jour un dégagement minimum de 8 pouces (21 centimètres) du tapis roulant
le plus proche ou de toute autre obstruction.
?
Ne localisez pas le tapis roulant à moins de 30 pouces (76 centimètres) d'un téléviseur.
?
Ne localisez pas le tapis roulant dehors, près des piscines, ou dans les zones du humidité élevé.
?
Placez le CORDON de SECTEUR parallèle à, mais loin de, l'avant du tapis roulant.
?
Vérifiez le contenu du carton de la livraison contre les pièces d' accompagnement énumérant avant de placer
les cartons et d'expédier le matériel de côté. Si des pièces sont manquantes, les services de support à la
clientèle de forme physique de la vie de contact au nombre ont énuméré à la page arrière de ce livret
d'instruction d'installation. Économiser les cartons d'expédition en cas de retour.
?
Lisez le manuel entier d'exécution avant d'essayer d'actionner cette machine car c'est essentiel pour l'usage
approprié. Le manuel explique comment utiliser correctement le tapis roulant et vous aide.
TOOLS REQUIRED FOR ASSEMBLY... Phillips screwdriver, hex key wrench set
PARTS DESCRIPTION
1
MONOCOLUMN
Qty: 1
2
3
0K40-01093-0001
HANDLEBAR WITH GRIPS
Qty: 1
4
Qty: 2
6
SCREW:
MONOCOLUMN TO TREADMILL FRAME
0017-00101-0815
SCREWS:
HANDLEBAR TO VERTICAL HANDRAILS
0017-00101-1159
VERTICAL HANDRAILS
Qty: 2
8
0K40-01186-0003
SCREWS: (BOTTOM)
5
7
AK40-00069-0000
HEX KEY SCREWS:
HANDLEBAR TO MONOCOLUMN
0017-00101-1096
SCREWS: (TOP)
HANDRAIL BASE TO SIDE MOUNTING BRACKETS (2”)
Qty: 1
Qty: 2
Qty: 2
Qty: 2
HANDRAIL BASE TO SIDE MOUNTING BRACKETS (2 1/2”)
9
0017-00101-1309
ENDCAP: RIGHT
Qty: 1
10
0017-00101-1319
ENDCAP: LEFT
Qty: 1
11
0K40-01086-0007
STOP KEY
Qty: 1
12
0K40-01086-0008
WASHER / COVER
Qty: 4
HANDRAIL BASE TO SIDE MOUNTING BRACKETS
0K40-01205-0000
13
AK40-00035-0000
SCREWS: VENT COVER
Qty: 2
14
VENT COVER
Qty: 1
15
0017-00101-1239
SCREWS: END CAPS
Qty: 6
16
AK40-00039-0001
DISPLAY CONSOLE
Qty: 1
17
0017-00101-1033
SCREWS:
Qty: 2
DISPLAY CONSOLE TO MONOCOLUMN
0017-00101-1159
2
13
4 17
7
5
8
15
12
PARTS DESCRIPTION
(Continued)
5
16
11
4
3
6
6
17
10
9
1
15
12
7
8
12
2
14
13
Step 1
Snap the VENT COVER off the MOTOR COVER (A) by pulling
outward. Carefully untie and uncoil the WIRE HARNESS (B)
tucked into the front center cutout of the MOTOR COVER. Pull
gently on the WIRE HARNESS to remove any slack.
C
B
1
Step 2
Lay the MONOCOLUMN (#1) on the STRIDING BELT and feed
the WIRE HARNESS CONNECTOR (C) into the access hole
provided near the bottom front side of the MONOCOLUMN. The
WIRE HARNESS should exit through the top on the user side
(toward the STRIDING BELT) of the metal bar welded across the
top center of the MONOCOLUMN.
A
Step 3
Slide the MONOCOLUMN (#1) into position through the UBRACKET (D) in the center of the MOTOR COVER (A). The large
access hole on the front side of the MONOCOLUMN should be
2
placed down and toward the front of the machine when properly
installed. Secure the MONOCOLUMN in position by lightly
tightening the nuts on the U-BRACKET. Insert the Phillips SCREW (#2) through the frame and into the bottom
hole of the MONOCOLUMN. Tighten the SCREW until finger-tight only.
Step 4
Insert the ends of the VERTICAL HANDRAILS (#6) into
the matching ends of the foam padded HANDLEBAR (#3).
Align the screw holes and secure each vertical post in
place with a loosely installed SCREW (#4). Slide each foot
of the completed HANDLEBAR/HANDRAIL ASSEMBLY
into the MOUNTING BRACKETS (E) located on either
side of the treadmill. Install the two 2” SCREWS (#7) and
WASHERS/COVERS (#12) and the two 2 1/2” SCREWS
(#8) and WASHERS/COVERS (#12) until finger-tight only
to hold the HANDLEBAR/HANDRAIL ASSEMBLY in
position with the MONOCOLUMN (#1).
5
4
3
6
6
D
1
NOTE: THE WASHER / COVERS (#12) ARE CURVED TO
MATCH THE VERTICAL HANDRAILS (#6). BE SURE TO
ALIGN THE WASHER / COVERS PROPERLY BEFORE
TIGHTENING THE SCREWS (#7 & #8).
12
7
8
D
12
NOTE: LA RONDELLE / COUVERTURES (# 12) SONT
COURBÉES POUR APPARIER LES BALUSTRADES
VERTICALES (# 6). SOYEZ SÛR D'ALIGNER LA
RONDELLE / COUVERTURES CORRECTEMENT AVANT
DE SERRER LES VIS (#7 & #8).
E
Step 5
Secure the HANDLEBAR (#3) tightly to top of the MONOCOLUMN (#1)
with two hex key SCREWS (#5).
10
Step 6
Tighten the U-BRACKET (D) nuts and all previously installed SCREWS
to secure all installations to this point.
Step 7
Position the LEFT and RIGHT ENDCAPS (#9 & #10) and secure them
with three each of the six SCREWS (#15) provided.
9
15
C
Step 8
Press the VENT COVER (14) into position on the
MOTOR COVER (A). Install the two SCREWS
(#19) into the corresponding holes on the sides of
the VENT COVER and the notch of the MOTOR
COVER and secure in place.
G
13
Step 9
Plug the 12-PIN CONNECTOR (12P) of the WIRE HARNESS (B) protruding from the top of the MONOCOLUMN
(#1) into the corresponding PC BOARD CONNECTOR located on the back of the DISPLAY CONSOLE (#16). Once
connected, feed the excess cable carefully back into the top of the MONOCOLUMN and lower the DISPLAY
CONSOLE into position on the MONOCOLUMN. Secure the DISPLAY CONSOLE to the MONOCOLUMN with the
two SCREWS (#17).
Step 10
Place the magnet side of the STOP KEY (#11) in the
space provided on the face of the DISPLAY CONSOLE
(#16). Check to ensure that the ON/OFF switch, located
next to the POWER CORD point of entry, is in the OFF
[O] position. Plug the treadmill POWER CORD into a
properly grounded outlet and change the switch setting to
the ON [I] position.
16
17
12P
B
16
1
Step 11
The treadmill STRIDING BELT is properly centered at the
factory. However, the LEVELING LEGS (F) may need to be
adjusted once the unit is placed in its intended location.
11
Step 12
Check to insure that the STRIDING BELT is
centered and tensioned properly according to the
instructions in the Operation Manual before running.
Failure to do so could cause damage to the
STRIDING BELT.
F
After placing the unit in its intended location for use, begin a Life Fitness workout program (see Operating
Instructions & Program Descriptions) but DO NOT run. It is important to ensure that the STRIDING BELT remains
centered during operation. If the BELT drifts to the RIGHT, see Figure A.. If the BELT drifts to the LEFT, see
Figure B.
NOTE: IT IS EXTREMELY IMPORTANT THAT THE TREADMILL LEVELING LEGS BE CORRECTLY
ADJUSTED FOR PROPER OPERATION. AN UNBALANCED UNIT MAY CAUSE STRIDING BELT
MISALIGNMENT AND POSSIBLY DAMAGE THE TREADMILL.
NOTE: IL EST EXTRÊMEMENT IMPORTANT QUE LE TAPIS ROULANT NIVELANT DES JAMBES SOIT
CORRECTEMENT AJUSTÉ À L'CEXÉCUTION APPROPRIÉE. UNE UNITÉ NON ÉQUILIBRÉE PEUT CAUSER
LA DÉVIATION D'ALIGNEMENT DE CEINTURE DE PROGRÈS ET PROBABLEMENT
ENDOMMAGER LE TAPIS ROULANT.
Before attempting to operate your Life Fitness treadmill, it is imperative that
you familiarize yourself with the contents of the Operation Manual. If your
treadmill does not respond as described in the OPERATION MANUAL
contact:
Life Fitness Customer Support Services
at (800) 351-3737 or (847) 451-0036
Prior to your call, please be sure you have located and noted the MODEL and SERIAL NUMBER (G) of your
Life Fitness treadmill. This information is contained on a label located on the front of the lift crossbar of the
treadmill.
Copyright 1999 Brunswick Corporation. All rights reserved. Life Fitness is a registered trademark of Brunswick Corporation.
M051-00K20-C078
G
2/99